Allison B 300 Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 396

background image

W T E C I I E L E C T RO N I C C O N T RO L S T RO U B L E S H O OT I N G M A N UA L

E–32

Copyright © 1998 General Motors Corp.

APPENDIX E — CONNECTOR PART NUMBERS, TERMINAL PART

NUMBERS, TOOL PART NUMBERS, AND REPAIR INSTRUCTIONS

D.

Terminal Insertion (ECD Bulkhead)

NOTE:

If replacing an outside grommet (refer to Figure E–9 showing the ECD bulkhead), ensure the
grommet is correctly installed. Each grommet hole is marked with the terminal ID of the wire that
passes through that hole. The grommet holes match the pattern of either the pins or sockets in the
connector. One side of the grommet is marked “PIN” and the other “SKT” or “SOC.” “PIN” indicates
the pin (receptacle) side of the connector and “SKT” or “SOC” the socket (plug) side. When installing
the outer grommet in the receptacle, ensure “PIN” is showing and positioned so that the “A” terminal
ID on the outer grommet aligns with the “A” terminal ID on the inner grommet. When installing the
outer grommet in the plug, “SKT” or “SOC” must be showing and positioned so that the “A” terminal
ID on the outer grommet aligns with the “A” terminal ID on the inner grommet. Reversing “PIN” and
“SKT” or “SOC” sides of the grommet will cause the grommet holes to be misaligned with the holes
in either the receptacle or plug. Perform Steps 1 and 2 only if the outer grommet has been removed.

1. Place the correct side of the grommet upwards with the inner and outer grommet “A” terminal ID

aligned.

2. Insert two cavity plugs in unused cavities to retain the grommet.

NOTE:

When using remover/inserter tool J 41194, take care not to break the tip of the tool. Lay the wire in
the widest part of the wire slot and work toward the tool tip.

1. Place the terminal and wire in the end of extractor/inserter tool J 41194.

2. Insert the tool through the grommet, into the back of the connector, and push until the terminal is

seated. Remove the remover/inserter tool.

3. Insert cavity plugs into all unused cavities.

4. Wrap plastic electrical tape around the wire bundle.

5. Reassemble the connector in the reverse order of disassembly.

E.

Terminal Insertion (all connectors except ECD bulkhead)

1. Insert wire with crimped terminal through the proper hole in the grommet.

2. Keep pushing on wire until the terminal “locks” into position.

«
...
267
268
269
270
271
...
»

Содержание B 300













































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B 300

Spacemaker 7-5400

Бренд: GE Страницы: 12

Бренд: HK Audio Страницы: 20

DigiTRU Diversity UB-33B

Бренд: Nady Systems Страницы: 6

Бренд: Olympus Страницы: 2

Бренд: AmpliVox Страницы: 8

Бренд: Hama Страницы: 76

Бренд: Paso Страницы: 16

Бренд: Blaupunkt Страницы: 8

Бренд: MAJORITY Страницы: 33

BeamPlex BRU-150

Бренд: Beamreach networks Страницы: 8

Бренд: Curtis Страницы: 14

Бренд: Gradus Group Страницы: 16

Бренд: Baxi Страницы: 98

Бренд: W Audio Страницы: 8

Бренд: Nady Systems Страницы: 12

Бренд: Marantz Страницы: 2

Бренд: Aiwa Страницы: 62

Бренд: i.safe MOBILE Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды