Allison B 300 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 396

Allison B 300 Скачать руководство пользователя страница 13

Copyright © 1998 General Motors Corp.

1–7

GENERAL DESCRIPTION

W T E C I I E L E C T RO N I C C O N T RO L S T RO U B L E S H O OT I N G M A N UA L

1–7.

WIRING HARNESSES

A.

External Wiring Harness

(Figures 1–10 and 1–11)

The external wiring harness provides a connection between the ECU, the transmission (including engine,
turbine, and output speed sensors), the throttle position sensor, the vehicle interface module (VIM),
retarder control module, shift selectors, diagnostic tool connector, retarder, retarder temperature sensor,
accumulator, and vehicle interface. Many harnesses will include a bulkhead to separate cab and chassis
components. Also, many different styles and materials for harnesses are likely to be encountered.

NOTE:

Allison Transmission is providing for service of WTEC II wiring harnesses and wiring harness
components as follows: (See Service Information Letter 1-WT-97 for further information.)

•

Repair parts for the internal wiring harness and for wiring harness components attached to the shift selector
will be available through the Allison Transmission Parts Distribution Center (PDC). Use the P/N from your
appropriate parts catalog or from Appendix E in this manual. Allison Transmission is responsible for
warranty on these parts.

•

Since January, 1998, all WTEC II external harnesses and external harness components must be obtained
from St. Clair Technologies Inc. (SCTI). SCTI provides parts to any Allison customer or OEM and is
responsible for warranty on these parts. SCTI recognizes ATD, manufacturers, and SCTI part numbers.
SCTI provides a technical HELPLINE at 519-627-1673 (Wallaceburg). SCTI has parts catalogs available.
The SCTI addresses and phone numbers for parts outlets are:

Figure 1–10. WTEC II External Wiring Harness (Units Produced Before 9/94)

St. Clair Technologies, Inc.
1050 Old Glass Road
Wallaceburg, Ontario, Canada, N8A 3T2
Phone: (519) 627-1673
Fax: (519) 627-4227

St. Clair Technologies, Inc.
1111 Mikesell Street
Charlotte, Michigan 48813
Phone: (517) 541-8166
Fax: (517) 541-8167

St. Clair Technologies, Inc.
c/o Mequilas Tetakawi
Carr. Internationale KM 1969
Guadalajara – Nogales, KM2
Empalme, Sonora, Mexico
Phone: 011-52-622-34661
Fax: 011-52-622-34662

OPTIONAL

DEUTSCH DDR

CONNECTOR

VEHICLE

INTERFACE

MODULE

(VIM)

CONNECTOR

MD/B 300/B 400

RETARDER CONNECTOR

(INCLUDES OUTPUT

SPEED SENSOR)

MD 3070

TRANSFER CASE

CONNECTOR

OUTPUT SPEED

SENSOR

*CONNECTOR

TRANSMISSION

CONNECTOR

ENGINE

SPEED

SENSOR

CONNECTOR

V01647

TPS

CONNECTOR

TURBINE

SPEED

SENSOR

CONNECTOR

(HD/B 500)

REMOTE SERIAL

INTERFACE

CONNECTOR

RETARDER “K”

CONNECTOR

(HD/B 500)

HD/MD/B RETARDER

ACCUMULATOR “H”

SOLENOID

CONNECTOR

OPTIONAL

BULKHEAD

CONNECTOR

WIRING

HARNESS

NOTE: Illustration is not to scale.

*All HD/B 500 models

All Non-Retarder MD/B 300/B 400 models

RETARDER

MODULATION

REQUEST (RMR)

SENSOR CONNECTOR

ELECTRONIC CONTROL UNIT

(ECU)

CONNECTORS

DIAGNOSTIC

DATA READER (DDR)

CONNECTOR

VEHICLE

INTERFACE

WIRING

(VIW)

CONNECTOR

HD/B 500

RETARDER

TEMPERATURE

SENSOR

CONNECTOR

«
...
11
12
13
14
15
...
»

Содержание B 300













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды