Allied A97USMV Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 78

background image

506887-01

Page 20 of 78

Issue 1213

Table 6

Maximum Allowable Vent pipe Length without Insulation in Unconditioned Space for Winter Design

Temperatures Modulating High Efficiency Furnace

¹Refer to 99% Minimum Design Temperature table provided in the current edition of the ASHRAE Fundamentals Handbook.
NOTE: Maximum unisulated vent lengths listed cannot exceedd the maximum allowable intake or exhaust vent length listed in Table 5.

General Guidelines for Vent Terminations

In Direct Vent applications, combustion air is taken from
outdoors and the flue gases are discharged to the outdoors.
This gas furnace is classified as a direct vent, Category IV
gas furnace.

In Direct Vent applications, the vent termination is limited
by local building codes. In the absence of local codes, refer
to the current National Fuel Gas Code ANSI Z223-1/NFPA
54 in U.S.A., and current CSA-B149 Natural Gas and
Propane Installation Codes in Canada for details.

Position termination according to location given in Figure
20. In addition, position termination so it is free from any
obstructions and 12" above the average snow accumulation.

At vent termination, care must be taken to maintain
protective coatings over building materials (prolonged
exposure to exhaust condensate can destroy protective
coatings). It is recommended that the exhaust outlet not
be located within 6 feet (1.8m) of a condensing unit because
the condensate can damage the painted coating.

NOTE:

See Table

6

for maximum allowed exhaust pipe

length without insulation in unconditioned space during

winter design temperatures below 32

°

F

0

°

C)

.

If equired

exhaust pipe should be insulated with

1

/

2

"

(13mm) Armaflex

or equivalent

.

In extreme cold climate areas

,

3

/

4

"

(19mm)

Armaflex or equivalent may be necessary

.

Insulation on

outside runs of exhaust pipe must be painted or wrapped
to protect insulation from deterioration

.

Exhaust pipe

insulation may not be necessary in some specific
applications

.

Do not use screens or perforated metal in exhaust
terminations. Doing so will cause freeze-ups and may
block the terminations.

IMPORTANT

FOR CANADIAN INSTALLATIONS ONLY:

In accorddance to CSA International B149 installation
codes, the minimum allowed distance between the
combustion air intake inlet and the exhaust outlet of other
appliances shall not be less than 12 inches (305 mm).

IMPORTANT

«
...
18
19
20
21
22
...
»

Содержание A97USMV















































































Отзывы:

Нет отзывов

Похожие инструкции для A97USMV

Бренд: WaterFurnace Страницы: 28

Habanero P1012726

Бренд: Ideal Vacuum Страницы: 19

Бренд: Lifebreath Страницы: 16

Бренд: Lennox Страницы: 6

Бренд: Lennox Страницы: 32

Бренд: Carrier Страницы: 11

Бренд: United States Stove Company Страницы: 2

Бренд: HumanLab Страницы: 18

ecoTEC pro VUW 6/5-3 Series

Бренд: Vaillant Страницы: 60

Бренд: Trane Страницы: 40

Бренд: Trane Страницы: 44

Бренд: Trane Страницы: 56

Бренд: Trane Страницы: 64

Бренд: ETL Страницы: 27

Бренд: Clean Energy Страницы: 78

1522 2-STAGE & R-25

Бренд: Atwood Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды