Allied Telesis 2914 Series Скачать руководство пользователя страница 19

Страница: 19 / 114

Chapter 1: Introduction

Twisted Pair

Copper Port

The AT-2914GP/SP network adapter is equipped with a PoE+ copper port

for a 10/100/1000BASE-T twisted pair cable. See Figure 6.

Figure 6. Twisted Pair Port and LEDs

The minimum cable requirement for the AT-2914GP/SP network adapter

is a TIA/EIA 568-B-compliant Enhanced 5 (Cat 5e) unshielded cable.

The twisted pair port has two LEDs. For link states and descriptions, see

Table 2.

LED for Fiber Optic Port

LED for Twisted Pair Port

Table 2. LED Status for the Twisted Pair Port on AT-2914GP/SP

LED

State

Description

Top-left LED

(For Twisted

Pair Port)

Valid link on the twisted pair port

Off

No link on the twisted pair port

Flashing The twisted pair port is receiving or

transmitting network packets.

Top-right LED

(For Fiber Port)

Valid link on the fiber optic port

Off

No link on the fiber optic port

Flashing The fiber optic port is receiving or

transmitting network packets.

Содержание 2914 Series



















































































































Результаты поиска

Содержание 2914 Series

Отзывы:

Allied Telesis 2914 Series, Инструкция по установке и эксплуатации, Страница: 19 / 114

Результаты поиска

Содержание 2914 Series

Отзывы: