Preliminary Information
About the Control
This control is an advanced, programmable computer that lets the
owner control machine features by pressing a sequence of SE-
LECT CYCLE pads. Refer to
.
The control allows the owner to program custom cycles, set vend
prices, retrieve audit information, run diagnostic tests, program
special vend features and other programmable features. Refer to
Programming Control for a list of features. Dryers shipped from
the factory have a default cycle (MED TEMP) built in. However,
the owner can change the default cycle, or any cycle, as needs
permit.
IMPORTANT: In the event of a power failure, the control
will not have to be reprogrammed. It is designed with a
memory system that will remember how it was pro-
grammed (for up to 10 years) until the electrical power
is restored.
IMPORTANT: It is extremely important that the dryer
has a positive ground and that all mechanical and elec-
trical connections to the control are made before ap-
plying power to or operating the dryer.
Glossary of Terms
The following are a few terms and abbreviations to learn. These
are referred to throughout the instructions.
Display – This term refers to the window area of the control that
displays words and values.
LED (Light Emitting Diode) – This term refers to the lights next
to the keypads and status words of the control.
IrDA – Infra-red External Device
FEC – Front End Control
I/O Board – Input/Output Board
OPL – On Premises Laundry
Power Failure Recovery
If a cycle is in progress and the power fails, the cycle status is
saved in memory. When the power recovers, the dryer will re-
sume into the previously active cycle (if so programmed by the
owner), by pressing the START pad. If the power failure occurs
while the control is in a fatal error mode, it will return to Ready
Mode upon recovery.
The owner may program a special feature called POWER FAIL
RESET which sets a maximum power failure duration before
vend is entered and cycle progress is lost. To program this fea-
ture, refer to
.
If the length of the power failure is greater than the POWER
FAIL RESET time, the control will end the cycle and the display
will revert back to the Ready Mode rather than resume the previ-
ously active cycle. If the length of the power failure is less than
the POWER FAIL RESET time and the power failure is greater
than 2 seconds, or the POWER FAIL RESET is turned off, the
dryer will enter START mode.
Communications
The control may be programmed manually, by infra-red commu-
nication with an external device or by the network. A limited
number of features can be programmed by a card reader.
The control may be programmed manually or by infra-red com-
munication with an external device. A limited number of features
can be programmed by a card reader.
The control may be programmed manually. A limited number of
features can be programmed by a card reader.
The control may be programmed manually or by infra-red com-
munication with an external device.
An external device, such as a PDA, allows the owner to program
and retrieve information from the control without touching the
keypad. An external device greatly expands the programming op-
tions available to the owner. However, it is not required to pro-
gram and operate the machine. The operation of an external de-
vice and the advanced features available are covered separately in
the instructions included with the external device software. Con-
tact Alliance Laundry Systems for a list of approved PDAs and
other external devices.
Infra-red Communications
An external device, such as a PDA, allows the owner to program
and retrieve information from the control without touching the
keypad. An external device greatly expands the programming op-
tions available to the owner. However, the external device is not
required to program and operate the machine. The operation of an
external device and the advanced features available are covered
separately in the instructions included with the external device
software. Contact Alliance Laundry Systems for a list of ap-
proved PDAs and other external devices.
Serial Card Reader Communications (Card Models
Only)
The control will accept communication with a serial card reader
in order to perform vending transactions when a card is inserted
to pay for cycles. The card reader can also allow the owner to
program a limited number of features and collect audit informa-
tion.
For detailed information on serial card reader communications,
refer to instructions included with card reader.
Preliminary Information
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7
Part No. D515810ENR3
Содержание PD3JGBGS403UG01
Страница 2: ......
