Alliance Laundry Systems BFNBCASG113TN01 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 51

background image

Factory Test Quick Reference Chart

Display

Test Mode

Comments

8888

Display Test

All LEDs and display segments will
light.

droP

or

drCL

Door Switch Test

droP

is displayed when loading door is

open.

drCL

is displayed when loading

door is closed.

dbXX

Driver Type and Driver Version Number

Driver board version display when XX is
the driver software version number.

drLo

or

drUL

Door Lock Test

When step is entered, control will lock
door and will then check to make sure
door is locked. drLo is displayed if door
is locked. drUL is displayed if door is un-
locked.

CLdE

Cold/Detergent Fill

Cold Water Fill valve and Detergent/
Bleach valve are turned on.

HoSF

Hot/Softener Fill

Hot Water Fill valve and Softener valve
are turned on.

PrSr

Pressure Sensor Fill

This step checks the water level input.
The display shows

PrSt

, and all water

valves turn on. When the Water Fill Lev-
el is satisfied, the water valves are turned
off. If the Start key is pressed and the
Water Fill level is not satisfied, the con-
trol will not advance to the next cycle
step.

oFLo

Overflow Test

All water and dispenser valves are turned
on. When the overflow level is reached
the water valves are turned off. If the
START (enter) key is pressed and the
Water Fill level is not satisfied, the con-
trol will not advance to the next cycle
step.

LoAg

Low Agitate

Machine enters low agitate.

rEAg

Regular Agitate

Machine enters regular agitate.

PUNP

or

drAi

Pump/Gravity Drain Test

Pump is turned on or gravity drain is
opened. The control will not advance to
next step until drum is empty.

RPM speed displayed

XXXX

Spin Test

Machine will attempt to spin up to 1200
RPMs.

Table 7

continues...

Testing Machine and Electronic Control Functions

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

39

Part No. 805407R6

«
...
37
38
39
40
41
...
»

Содержание BFNBCASG113TN01




















































Отзывы:

Нет отзывов

Похожие инструкции для BFNBCASG113TN01

Бренд: UNITED Страницы: 80

Бренд: Ariston Страницы: 16

FAVORIT 64080 i

Бренд: AEG Electrolux Страницы: 44

Бренд: GE Страницы: 3

Бренд: Euromaid Страницы: 7

Бренд: Zline Страницы: 28

Бренд: Parker Страницы: 56

NovaWheel NWB- DC+ Series

Бренд: NovaTec Страницы: 32

Бренд: Technika Страницы: 42

Бренд: TSM Страницы: 102

Performa LAW2400

Бренд: Maytag Страницы: 12

Profile PDT750SMFES

Бренд: GE Страницы: 48

IVC 60/12-1 Ec H Z22

Бренд: Kärcher Страницы: 372

Бренд: Fisher & Paykel Страницы: 40

Бренд: DAN DRYER Страницы: 2

Бренд: Cub Cadet Страницы: 72

Бренд: Asco Страницы: 16

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды