Alliance Laundry Systems BFNBCASG113TN01 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 51

background image

Display Identification

Light Emitting Diodes (LEDs)

LIGHT EMITTING DIODES (LEDs) are used to indicate the
chosen cycle and cycle status. See below for information on each
LED.

CYCLE LED

CYCLE LED will remain lit the entire cycle.

WASH LED

WASH LED is lit at the beginning of a wash portion of the cycle
and will remain lit until the wash is complete.

RINSE LED

RINSE LED is lit at the beginning of a rinse portion of the cycle
and will remain lit until the rinse is complete.

SPIN LED

SPIN LED is lit during the Final Spin portion of the cycle.

DOOR LOCKED LED

DOOR LOCKED LED is lit whenever the door is locked. The
door can't be opened when this LED is lit.

7-Segment Digits

The 7-SEGMENT DIGITS are used to display the time remain-
ing in a cycle, vend price, error messages and descriptive codes.
During diagnostic testing or manual programming of the control,
these digits will display descriptive codes and values.

Display Identification

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

11

Part No. 805407R6

«
...
9
10
11
12
13
...
»

Содержание BFNBCASG113TN01




















































Отзывы:

Нет отзывов

Похожие инструкции для BFNBCASG113TN01

Бренд: Samsung Страницы: 10

Бренд: Samsung Страницы: 9

Бренд: Samsung Страницы: 7

Бренд: Samsung Страницы: 12

Бренд: IFB Страницы: 24

Бренд: Infiniton Страницы: 127

Бренд: Aurora Страницы: 8

Бренд: Fisher & Paykel Страницы: 6

Бренд: Maytag Страницы: 51

Custom Front DFUD042

Бренд: Viking Страницы: 34

Бренд: GE Страницы: 20

Бренд: Magic Chef Страницы: 25

DPSE810GGWT - ProfileTM 7.0 cu. Ft. Gas...

Бренд: GE Страницы: 32

Бренд: Maidaid Halcyon Страницы: 17

HDEm 2000 Top Line

Бренд: Elektro Maschinen Страницы: 52

Бренд: KAI Страницы: 13

Бренд: Andis Страницы: 20

Бренд: Parmco Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды