Alliance Laundry Systems BFNBCASG113TN01 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 51

background image

Entering the Manual Mode

How to Enter the Manual Mode

For programming, testing, and retrieving information from the
control, it is often necessary to enter the Manual Mode by follow-
ing the four simple steps below. For an overview of entering the
Manual Mode, refer to the flowchart on the following page.
1. If accessing Diagnostic Tests that take control of machine op-

eration, be sure the washer is in the Start or Ready Mode be-
fore continuing to step 2. If the washer is in an active cycle,
rapid advance through the cycle. Refer to

Rapid Advance

.

2. Stacked Washers and Dryers, 10 Degree Front Control Wash-

ers and Coin Rear Control Washers through Serial No.
1810000001: Open the service door. The coin vault switch
must be closed.

3. All Other Models: Open the service door, if necessary, and

unplug bullet connector.

4. While pressing and holding the PERM PRESS WARM key-

pad with one hand, press the NORMAL HOT keypad with the
other hand.

5. The display will show

rAPd

.

6. Press the NORMAL WARM (

∧

) or the DELICATES COLD

(

∨

) keypad to scroll through the options until the desired op-

tion appears in the display.

7. Press the START (enter) keypad.

NOTE: After entering Manual Mode, if no keypads
are pressed for 4.25 minutes, the control will return
to the previous mode of operation.

8. To exit, press the PERM PRESS WARM ( < ) keypad. The

control will revert back to Ready Mode.

Manual Mode Navigation

Manual Mode is broken into five groups: Manual Programming,
Manual Read Audit, Manual Reset, Manual Rapid Advance and
Manual Diagnostics.

The manual features available in each group are as follows (the
menu shown on the display in this mode is in parentheses).

• Manual Programming (

Prog

)

• Manual Read Audit (

AUdt

)

• Manual Reset (

rSEt

)

• Rapid Advance (

rAPd

)

• Manual Diagnostic Tests (

diAg

)

Entering the Manual Mode

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

18

Part No. 805407R6

«
...
16
17
18
19
20
...
»

Содержание BFNBCASG113TN01




















































Отзывы:

Нет отзывов

Похожие инструкции для BFNBCASG113TN01

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 40

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 8

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 10

HW-C1470TVE ME-U

Бренд: Haier Страницы: 19

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 19

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды