Allestec EDISON ONGUARD 1604 Скачать руководство пользователя страница 25

Страница: 25 / 28

Page 25

11. MAINTENANCE AND TROUBLESHOOTING

There is no annual maintenance required for the series 1604 monitor, unless the local authority having

jurisdiction has established such a routine. If there is time of no operation, the unit could be cleaned by

holding an air compressor near the air vent holes, at no more than 45 psi and carefully blow away any

accumulated dust.

12. WARRANTY

Allestec Corporation will provide warranty for the monitor for a period of three years. Allestec agrees to

repair or replace any component or subassembly it deems necessary to fulfill the obligation of the war-

ranty. The warranty does not include abuse to the unit, mechanical or electrical. Also not covered under

the warranty is water, chemical, particle damage, acts of God, lightning, and other external influences.

To service your unit, send the monitor to your distributor and provide a contact name with a phone num-

ber. State the nature of the problem, if known.

Specifications are subject to change without notice.

13. FIELD WIRE CHARACTERISTICS

(Chart is not utilized for RTD conductors)

WIRE RESISTANCE CHART

WIRE SIZES

(Annealed Copper)

Ohms Per 1000 feet (304.8m)

Diameter

AWG

Area (mils) Circular Mils

0°C

32ºF

20°C

68ºF

50°C

122ºF

101.90

10380.00

0.9203

0.9989

1.1170

80.81

6530.00

1.4630

1.5880

1.7750

64.08

4107.00

2.3270

2.5250

2.8230

50.82

2583.00

3.7000

4.0160

4.8900

40.30

1624.00

5.8830

6.3850

7.1380

31.96

1022.00

9.3550

10.1500

11.3500

25.35

642.00

14.8700

16.1400

18.0500

20.10

404.00

23.6500

25.6700

28.7000

15.94

254.10

37.6100

40.8100

45.6300

12.64

159.80

59.8000

64.9000

72.5500

10.03

100.50

95.0800

103.2000

115.4000

7.95

63.21

151.2000

164.1000

183.4000

WARNING: VERIFY THAT ANY EQUIPMENT TO BE WORKED ON IS REMOVED FROM

THE POWER SOURCE UNTIL THE WORK IS COMPLETE.

Содержание EDISON ONGUARD 1604





























Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды

Allestec EDISON ONGUARD 1604, Руководство по эксплуатации системы

Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды