Allestec EDISON ONGUARD 1604 Скачать руководство пользователя страница 15

Страница: 15 / 28

Page 15

3.11 SET UP SYSTEM

Returning to the Program Menu, select F2 to establish the

initial system configurations. Then select F1 later to estab-

lish specific RTD configurations. The ESC key may be se-

lected at any time to back out of the selection.

3.12 SYSTEM TIME

Select F1 to enable the cursor field. Enter military time in

this format: HH:MM:SS then press Enter or PgDn to pro-

ceed. PgUp previous menu.

3.13 SYSTEM DATE

Select F1 to change the date. Enter the date in this format

MM/DD/YY then select Enter or PgDn to proceed. PgUp pre-

vious menu.

3.14 SYSTEM NAME

Enter a name unique for this monitor. When configuration

and history reports are viewed, this monitor name will ap-

pear. Some installations may incorporate several monitors.

Select F1 to edit, and enter or PgDn to save.

3.15 SYSTEM FAULT RELAY

(section 10)

This relay is common to all 4 RTD channels. F1 toggles and

selects the latching and non-latching operation of the system

fault relay. The fault relay output is accessible at TB3 figure

6. This relay is designed for failsafe (normally energized)

and remains in this condition unless power is removed from

the monitor or a fault occurs. Select PgDn to proceed. PgUp

previous menu.

3.16 PRE-ALARM RELAY

This relay is the RTD first temperature trip point relay and is

common to all 4 channels. This relay defaults to non-

latching. Select F1 to change to latching. The pre-alarm re-

lay output, figure 6, is accessible at TB3. Select PgDn to

proceed. PgUp previous menu.

3.17 PRE-ALARM MESSAGE

Enter F1 and type an optional message that references any

four channels to this pre-alarm. The pre-alarm occurs when

an RTD attains it’s first set-point threshold and trips the dedi-

cated pre-alarm relay. Refer to figure 6 for location of relay

contacts.

3.18 SAVING THE DATA for the F2 SET UP SYSTEM

Select PgDn to return to the main menu then select ESC,

then F1.

PRE-ALARM RELAY *

NON-LATCHING

F1-CHNG PGU/D-NXT

SYSTEM FAULT RELAY *

NON-LATCHING

F1-CHNG PGU/D-NXT

* SYSTEM NAME *

Pump #2

F1-CHNG PGU/D-NXT

* SYSTEM DATE *

MM/DD/YY

F1-CHNG PGU/D-NXT

* PROGRAM MENU *

F1 SET UP RTD

F2 SET UP SYSTEM

F3 CHANGE PASSWORD

* SYSTEM TIME *

HH:MM:SS

F1-CHNG PGU/D-NXT

PRE-ALARM MESSAGE *

F1-CHNG PGU/D-NXT

Содержание EDISON ONGUARD 1604





























Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды

Allestec EDISON ONGUARD 1604, Руководство по эксплуатации системы

Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды