Allestec EDISON ONGUARD 1604 Скачать руководство пользователя страница 19

Страница: 19 / 28

Page 19

5. SINGLE TEMPERATURE ALARMS

5.1 SYSTEM STATUS

The words “SYSTEM OK” will remain on the display unless an alarm, fault or enter program condition

occurs.

5.2 TEMPERATURE ALARMS

In the event any temperature attains an alarm set point, the common alarm relay (TB1) will trip as indi-

cated in the configuration menu. The beeper will turn on, and the display will brighten from its low inten-

sity to bright mode to identify the alarm parameters. The → NXT ALRM line will appear when there are

other active alarms to view. Navigate to menus to view and reset any alarms.

6. MULTIPLE TEMPERATURE ALARMS

In the event that multiple alarms occur, the first set point to sustain its threshold will be displayed.

Alarms that are received are placed in chronological order. The display automatically jumps to the next

incoming alarm if the acknowledgment is left unattended. The alarm-viewing structure of the display is

set up as a continuous spreadsheet so the administrator can CURSOR ► to a specific RTD number in

alarm and then CURSOR ▼ to the details. At any time cursor left Ctrl + CURSOR ► or right to jump to

the next column of another RTD. If the cursor is not in the top alarm menu and then shifted ◄► to the

next alarm, the cursor will jump to the top menu. The ALARM indicator flashes when the alarm is active

and goes solid when the alarm clears. When the alarm clears, reset it by selecting the ACK button on

the face plate.

* RTD #1 ALARM *

Pump Room #5

ACKNOWLEDGED

→ NXT ALM

* RTD #1 ALARM *

MODE: RISING

PLATINUM #8

↓

NX SCRN

ACKNOWLEDGE the ALARM

Select the ACK to acknowledge the alarm, and the word

“ACKNOWLEDGED” will appear in the menu, and the beep-

er will silence. The ALARM notice will flash as long as the

temperature remains in the alarm state.

VIEW THE ALARM CONTENTS

Select the VIEW button, then CURSOR ▼ to scroll through

alarm menus. Select VIEW to exit.

RESETTING THE ALARM

Select the ACK button to reset the alarm and save the event

to the history buffer. The alarm can be RESET in any ▼

menus if the alarm has cleared (ALARM stops flashing).

NOTE: The alarm will not reset if its sensor temperature re-

mains past the set point.

* RTD #1 ALARM *

SET POINT: 220 ° F

RTD READS: 225 ° F

↓

NX SCRN

ALARM MESSAGE *

Содержание EDISON ONGUARD 1604





























Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды

Allestec EDISON ONGUARD 1604, Руководство по эксплуатации системы

Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды