Allestec EDISON ONGUARD 1604 Скачать руководство пользователя страница 10

Страница: 10 / 28

Page 10

2.7 TEMPERATURE ALARM RELAY

Refer to the TB3 terminal strip in figure 6 for wiring the alarm relay dry contact. Connect devices to this

form C, (SPDT) relay to monitor the set point of any alarming RTD sensor. This relay is common to the

four channels of the monitor. The alarm relay will change state when a temperature enters the adminis-

trator defined temperature set point. The alarm relay functions with alarms on rising or falling.

NOTE: The monitor comes with all RTD channels disabled to alleviate possible alarms when the monitor

is first powered up.

2.8 POWER CONNECTION

Depending on the monitor power supply, connect the power requirement to the monitor terminal TB2 as

indicated in figure 6. Verify on the product ID label the correct power source prior to applying power to

the monitor. After all hardware devices have been mounted and connected together, power may be ap-

plied to the monitor.

2.9 INTERNAL COMPONENT BOARD DESCRIPTIONS

The three boards listed below are installed in the monitor and are not a component to be repaired by

unauthorized personnel. For repair, the monitor must be sent to the distributor where it was purchased.

2.10 PROCESSOR BOARD

This board incorporates the microprocessor, memory, display and all necessary components to allow

the process function of the monitor.

2.11 POWER SUPPLY BOARD

Power requirements for the monitor are provided by the power supply board. The input of the power

supply is transient protected from surges. The monitor power input is fuse protected and identified on

the circuit board. This fuse, (F1) is a 5mm, 1A Slo-blo. Refer to the monitor identification label to verify

the power supply voltage rating.

2.12 REAR TERMINAL BOARD

FIGURE 2

For convenient access, all con-

nections to the monitor are pro-

vided by this connector assem-

bly located at the rear at the

monitor. The connectors can

accommodate from 24 to 12

gage twisted conductors. The

system fault and alarm relay is

located on this board as well.

Refer to figure 6 for RTD, relay

and power connections.

Содержание EDISON ONGUARD 1604





























Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды

Allestec EDISON ONGUARD 1604, Руководство по эксплуатации системы

Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды