Allestec EDISON ONGUARD 1604 Скачать руководство пользователя страница 24

Страница: 24 / 28

Page 24

10. FAULT ACTIONS

If a system fault occurs, the display will brighten from its low intensity mode to identify the RTD ID number.

At the same time, the event will be recorded to the history buffer. Silence the beeper to proceed with cau-

tion to identify and correct the problem. During a fault, the fault relay (TB3) will trip until the fault is cleared

and the monitor is reset. Most faults can be attributed to the following detailed problems at the RTD.

* RTD 1 SYS FAULT *

RTD name field

ACKNOWLEDGE

TO SILENCE BEEPER:

Select the ACK button to silence the beeper.

TO RESET FAULT ALARM

The word FAULT will flash if the fault is active. When the fault

clears, the word FAULT will stop flashing and then the monitor

can be reset.

TO VIEW:

Select VIEW, then use the CURSOR ▼ to navigate to menus

for information. Select VIEW again to return to the fault alarm.

10.1 RTD SYSTEM FAULTS

1. Open RTD

2. Shorted RTD

3. RTD resistance is above or below the recommended range

as indicated in the temperature range chart below. The temper-

ature in the display will flash when out of range.

On a 3-wire RTD, the red or either one of the white signal wires

opening are considered the problem. Also, either white wire

shorting to the red can be the problem. Shorted or singular

opened white wires will not cause a fault but will influence the

temperature accuracy, depending on the length of the RTD

wires.

Menu indicates a system fault at RTD

ID #1.

10.2 EXCEEDING TEMPERATURE LIMITS

If a temperature drops below or exceeds the maximum value for the RTD type as indicated in the chart

below, the fault relay will change state. The fault relay performs an ‘OR” function for all four channels. All

exceeded temperatures must return to their authorized operating point before the fault relay is in normal

condition.

Sensor Type

Degrees F

Degrees C

Platinum #8

-202 to 1544

-130 to 840

Platinum #11

-202 to 1364

-130 to 740

Nickel #1,7

-94 to 572

-70 to 300

Copper #15

-58 to 482

-50 to 250

TEMPERATURE RANGES

WARNING: POWER MUST BE REMOVED FROM THE MONITOR BEFORE PERFORMING

ANY TROUBLESHOOTING.

Содержание EDISON ONGUARD 1604





























Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды

Allestec EDISON ONGUARD 1604, Руководство по эксплуатации системы

Результаты поиска

Содержание EDISON ONGUARD 1604

Отзывы:

Похожие инструкции для EDISON ONGUARD 1604

Бренды по названию

Популярные бренды