allen AT-16 Скачать руководство пользователя страница 43

Страница: 43 / 104

056841 - 01/2013

SECTION 3

SERVICE

Page 3-3

Pre-Cleaner Maintenance Procedure

This engine is equipped with a large capacity, dual element air filter—an oiled, foam pre-cleaner sur

rounds a high density paper element.

Every

25 hours

of operating time (more often under extremely dusty or dirty conditions) the oiled, foam

pre-cleaner needs washing and oiling. Remove, wash, dry and oil the pre-cleaner and replace as fol-

lows:

• Raise the bucket.

• Un-bolt and remove the rear engine housing cover and access the air filter from the rear. Remove

wing nut, air filter cover and paper element with foam pre-cleaner.

• Remove foam pre-cleaner from the paper element.

• Carefully check both elements for holes or tears and replace if damaged.

• Wash the foam pre-cleaner element in a solution of household detergent and warm water. Then, rinse

thoroughly removing all soap and squeeze out excess water;

DO NOT

wring. Allow the element to dry

thoroughly.

Note:

The engine will smoke during initial start-up if too much oil is left in the foam.

• Soak the foam pre-cleaner element in a clean engine oil, and squeeze out the excess oil. (Use paper

towel or similar absorbent tissue to blot/squeeze out excess oil.)

DO NOT

wring.

• Install pre-cleaner over paper air filter element.

• Install the air filter, air filter cover and wing nut. The wing nut must be finger tightened 1/2 to 1 full turn

after the nut contacts cover.

DO NOT

overtighten.

• Install the engine housing cover.

• Lower the bucket.

Air Filter Maintenance

WING NUT

COVER

FOAM PRE-CLEANER

PAPER ELEMENT

ENGINE MEMBER

Содержание AT-16









































































































Результаты поиска

Содержание AT-16

Отзывы:

Бренды по названию

Популярные бренды

allen AT-16, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание AT-16

Отзывы:

Бренды по названию

Популярные бренды