allen 069600 Скачать руководство пользователя

Страница: 52 / 60

SPN

Code

FMI

Code

Fault Check Description

Fault Detection Condition

Possible

Causes

23613

Maximum Positive Deviation of Rail

Pressure Exceeded

If the rail pressure governor deviation Rail_pDvt exceeds the limiting

value based on the engine speed Rail_pMeUnDvtMax_CUR an error will

be detected.

1. Leakage in the

high pressure
section

2. Injection nozzle

stuck in open
position

3. Worn high pres-

sure pump

4. Worn injector

(to high injector

back flow

quantity)

Fuel filter

clogged up

6. PSP (electric

pre-supply
pump) output
too low

If the rail pressure governor deviation

Rail_pDvt falls below the limiting value

Rail_pMeUnDvtMin_CUR and if the CP3

delivery quantity MeUn_dvolSet falls to

the threshold Rail_MeUnMon.dvolSet-

Min_C (-350 mm^3/s) an error will be

detected.

If the rail pressure governor deviation Rail_pDvt falls below the limiting

value Rail_pMeUnDvtMin_CUR and if the CP3 delivery quantity MeUn_

dvolSet falls to the threshold Rail_MeUnMon.dvolSetMin_C an error will

be detected.

1. Metering unit is

stuck in open
position

2. Zero delivery

throttle clogged
up

3. Metering unit

without power
due to electrical
error.

4. Pressure after

zero-delivery
throttle too high.

If the rail pressure RailP_pFlt exceeds

the limiting value Rail_MeUnMon.

pFltMax_C (1.750.000 hPa) an error will

be detected.

If the rail pressure RailP_pFlt exceeds the limiting value Rail_MeUnMon.

pFltMax_C an error will be detected.

1. Metering unit is

stuck in open
position

2. Zero delivery

throttle clogged
up

3. Metering unit

without power
due to electrical
error.

4. Pressure after

zero-delivery
throttle too high.

Leakage is detected based on fuel

quantity balance

If the high pressure pump delivery quantity ( MeUn_dvolSet) exceeds the

plausibility limit of the volume flow balance (evaluated over the product

life and supplemented to include tolerances) Rail_dvolMonMax_mp, an

error will be detected.

Maladjusted rail

pressure sensor,

defective high

pressure pump,

leakage,

Possible error in

the low pressure

stage, Back flow

too low

Fault Codes

SECTION 3

SERVICE

069971

Page 52

Содержание 069600





























































Результаты поиска

Содержание 069600

Отзывы:

Похожие инструкции для 069600

Бренды по названию

Популярные бренды

allen 069600, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание 069600

Отзывы:

Похожие инструкции для 069600

Бренды по названию

Популярные бренды