allen 069600 Скачать руководство пользователя

Страница: 50 / 60

SPN

Code

FMI

Code

Fault Check Description

Fault Detection Condition

Possible

Causes

20238

Diagnostic Fault Check to Report "WDA/

ABE Active" due to unknown reason

In the case of a non active shut-off path test (MoCSOP_stActMsg ==

FALSE) whose debounce OCWDA_CTDEBSOPNOTACTV* 10ms has

expired (counter OCWDA_ctDebSOPNotActv = 0) and an active ABE wire

due to undervoltage there is an undebounced defect detection after the

battery voltage BattU_u keeps greater than OCWDA_uBattMin_C (8V)

longer than the debounce time OCWDA_CTUBATTMX (100ms).

ECU Internal Fault

20251

Visibility of Software Resents in DSM

The evaluation of the reset reason will be done after every reset. De-

pending on the configured visibility of the current reset one of the fault

checks in the array will be set.

The evaluation of the reset reason will be done after every reset. De-

pending on the configured visibility of the current reset one of the fault

checks in the array will be set.

The evaluation of the reset reason will be done after every reset. De-

pending on the configured visibility of the current reset one of the fault

checks in the array will be set.

20276

Diagnostic Fault Check to Report the

Remote Accelerator Pedal Position Error

Implausible accelerator pedal voltage. The two voltage values (ADC_

VAL1, ADC_VAL2), detected by the accelerator pedal, are not plausible to

each other. If RMTAPP with LIS is used , defect is detected if there is a

implausibilty with LIS and RMTAPP1 voltage.

20282

Short Circuit to Battery on Out1 Error for

H-Bridge

Short Circuit to Battery at Out1 of TLE7209/CJ230 Error

Wiring Harness or

Component

Short Circuit to Battery on Out2 Error for

H-Bridge

Short Circuit to Battery at Out2 of TLE7209/CJ230 Error

Short Circuit to Ground on Out1 Error for

H-Bridge

Short Circuit to Ground at Out1 of TLE7209/CJ230 Error

Short Circuit to Ground on Out2 Error for

H-Bridge

Short Circuit to Ground at Out2 of TLE7209/CJ230 Error

Open Load Error for Power-stage

Open Load Error Monitoring for TLE7209/CJ230

Over Temperature Error for H-Bridge

Over Temperature Error Monitoring for TLE7209/CJ230

Wiring Harness

Component for

ECU Internal Fault

20288

DFC for Coding Error when Different

Coding Words were Received in a cod-

ing cycle

Glowing Problems

No Load Error for Low Voltage System

Short Circuit to Battery Error for Low

Voltage System

Short Circuit to Ground Error for Low

Voltage System

Over Temperature Error on ECU Power-

stage for Glow Plug Low voltage System

DFC for T30 Missing Error in GCU-T

DFC for Coding Error when Selected

Coding is not working

DFC for faulty Diagnostic Data

Transmission or Protocol Error

DFC for glow Module Error in GCU-T

Fault Codes

SECTION 3

SERVICE

069971

Page 50

Содержание 069600





























































Результаты поиска

Содержание 069600

Отзывы:

Похожие инструкции для 069600

Бренды по названию

Популярные бренды

allen 069600, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание 069600

Отзывы:

Похожие инструкции для 069600

Бренды по названию

Популярные бренды