manualshive.com logo in svg

allen 069600, Инструкция по безопасности и эксплуатации

"Подробное руководство по безопасности и эксплуатации для Allen 069600 доступно для бесплатного скачивания на нашем сайте. Это важное руководство содержит информацию о правильной эксплуатации продукта и обеспечении безопасности пользователей. Скачайте его сейчас с manualshive.com."

Поделиться
Скачать
background image

This section details the proper technique to utilize the Dolly Jack system in a safe 

manner to install concrete finishing pans. 

(NOTE: Images are for illustration purposes only)

Use the appropiate set of lifting jacks that are designed for the machine you are lifting.  

[See section "ACCESORIES" for appropriate dolly jack part number]

1.  Attach the front and rear dolly jacks into the machine at the receiving 

tube locations. 

2.  Slowly lift the machine in a safe manner to a height that is required to 

safely install the pans. This is typically 6"-8" above floor level. 

3.  Carefully slide the pans under the machine, making sure that you are 

aware of the corners of the blades as they are sharp.

4.  Align the pans so that the clips will not be crushed when the machine is 

lowered back down.

5.  Slowly lower the machine down onto the pans. Make sure the blades 

are going into the proper gaps. (Typically the pans can only be installed 
one way)

6.  Remove the dolly jacks from the machine

7.  Start the machine and slowly increase the throttle until the blades begin 

turning and engaging the pans.  The machine is now ready to finish the 
concrete utilizing the pans. 

NOTE

: Utilizing the lifting sling(bridle) and the dolly jacks are intended only 

for site transportation and the installation of pans and blades. DO NOT use 

them for regular maintenance without the additional use of jack stands to 

insure stability of the machine.

SECTION 1

SAFETY

069971

Page 23

Pan Installation Safety - Lifting Jacks

Содержание 069600





























































Отзывы:

Нет отзывов

Похожие инструкции для 069600

Бренды по названию

Популярные бренды

Загрузить еще бренды