allen 069600 Скачать руководство пользователя

Страница: 48 / 60

SPN

Code

FMI

Code

Fault Check Description

Fault Detection Condition

Possible

Causes

5324

Array of DFC's for Failure in i+1

Glow

Plug

Glowing Problems

5325

Array of DFC's for Short Circuit in i+1

Glow Plug

Array of DFC's for Failure in i+1

Glow

Plug

5326

Array of DFC's for Short Circuit in i+1

Glow Plug

Array of DFC's for Failure in i+1

Glow

Plug

5327

Array of DFC's for Short Circuit in i+1

Glow Plug

Array of DFC's for Failure in i+1

Glow

Plug

20201

SPI/COM-Errors of the Cy320

When Any Peripheral Monitoring Function Reports an Error

ECU Internal Fault

20220

Diagnostic Fault Check to Report the

NTP Error in ADC Monitoring

Error in the check with the No-Load Test Pulse Operation.

Diagnostic Fault Check to Report the

ADC Test Error

Implausible ADC test errors

It is checked whether MoCADC_ctDebTst > = MoCADC_ctDebTst_C (15

Events).

If yes the error is set. The diagnosis is carried out in the 40-ms interval.

Diagnostic Fault Check to Report the

Error in Voltage Ratio in ADC Monitoring

It is checked whether MoCADC_ctDebVltgRatio > = MoCADC_ctDebVlt-

gRatio_C (15 Events).

If yes the error is set. The diagnosis is carried out in the 40-ms interval.

20221

Diagnostic Fault Check to Report Errors

in Query-/Response-Communication

If there is no active shut-off path test (MoCSOP_stRdyMsg == TRUE)

and the error counter MoCCom_ctErrMM or MoCCom_ctErrFC is >=

MOCCOM_MM_STATUS_LIMIT_ERRORS (5) there is an undebounced

defect detection

20222

Diagnostic Fault Check to Report Errors

in SPI-Communication

If there is no active shut-off path test (MoCSOP_stRdyMsg == TRUE)

and the error counter MoCCom_ctErrMM or MoCCom_ctErrFC is >=

MOCCOM_MM_STATUS_LIMIT_ERRORS (5) there is an undebounced

defect detection

20223

Diagnostic Fault Check to Report

Multiple Error While Checking the

Complete ROM-Memory

If multiple errors are detected while testing the complete ROM-memory

(irreversibles error bit 2 in MoCMem_st is set)

there is an undebounced defect detection.

20224

Diagnostic Fault Check to Report the

Accelerator Pedal Position Error

Implausible accelerator pedal voltage. The two voltage values (ADC_VAL1

ADC_VAL2) detected by the accelerator pedal are not plausible to each

other.

20225

Diagnostic Fault Check to Report the

Engine Speed Error

Implausible engine speed. The engine speed value calculated in level 2

(MoFESpd_nEngL2_mp ) and Epm_nEngLRes (engine speed from level 1)

are not plausible to each other.

20226

Diagnostic Fault Check to Report the

Plausibility Error Between Level 1

Energizing Time and Level 2 Information

Implausible injection quantity.

It is tested if MoFInjDat_ctDebETErr >= MoFInjDat_ctDebETErr_C (5

Events).

In case of this the error is set. This diagnosis is processed in the 40ms

interval.

20227

Diagnostic Fault Check to Report the
Error Due to Plausibility Between the

Injection Begin v/s Injection Type

Implausible start of energizing angles.

It is tested if MoFInjDat_ctDebPhiErr >= MoFInjDat_ctDebPhiErr_C (5

Events). In case of this the error is set. This diagnosis is processed in the

40ms interval.

Fault Codes

SECTION 3

SERVICE

069971

Page 48

Содержание 069600





























































Результаты поиска

Содержание 069600

Отзывы:

Похожие инструкции для 069600

Бренды по названию

Популярные бренды

allen 069600, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание 069600

Отзывы:

Похожие инструкции для 069600

Бренды по названию

Популярные бренды