manualshive.com logo in svg

Allen-Bradley DeviceNet 1761-NET-DNI, Руководство пользователя, Страница: 68 / 101

Поделиться
Скачать
Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 68

1761-6.5

6-10

Setup, Programming, and Troubleshootin g

Troubleshooting

LED Indicators

The DeviceNet Interface has three LED indicators:

MOD LED (Module Status LED)

The module status LED provides information specific to the DNI.

LED

Color

Module Status LED

bicolor - red/green

Network Status LED

bicolor - red/green

RS-232 LED

green

LED Condition

DNI State

Problem/Indication

Off

Not Powered

The device may not be powered or

firmware unable to run.

Green

(1)

(1) Normal condition.

•

DNI Series A: Device

Operational

•

DNI Series B:

Device Scanning

The device is operating in a normal

condition.

Flashing Green

(1)

•

DNI Series A:

Device in Standby

•

DNI Series B:

Device Not Scanning

•

For DNI Series A only, the device may

be in Standby Mode; set to

operational.

•

For DNI Series B, I/O Scan (Polling

Enable) may need to be set (1).

Flashing Red

Minor Fault

Recoverable fault.

•

DNI may need to be commissioned

(the DNI will not operate when set to

the out-of-box defaults).

•

The device needs commissioning

due to missing, incomplete, or

incorrect configuration.

•

EEPROM may be corrupt,

re-commission the DNI.

Red

Unrecoverable Fault

The device has an unrecoverable fault

which requires the power to be cycled,

or the DNI may need to replaced.

Flashing Red-Green Device Self Testing

The device is in self test and should only

occur at power up or re set.

Содержание DeviceNet 1761-NET-DNI






































































































Отзывы:

Нет отзывов