Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 101

Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 32

1761-6.5

4-4

Installation and Wiring

Panel Mounting

1. Remove the mounting template from Appendix A of this document.

2. Secure the template to the mounting surface.

3. Drill holes through the template.

4. Remove the mounting template.

5. Mount the unit.

Network Port Wiring

DeviceNet Network

To properly design your DeviceNet network, you need Allen-Bradley
publication DN-6.7.2, DeviceNet Cable System Planning and Installation
Manual. This document provides design guidelines concerning wiring
practices, connectors, grounding, power budgeting, etc.

This publication is available from your Allen-Bradley distributor, or from
the Internet at http://www.theautomationbookstore.com.

Port Identification

Mounting Template

V–

CAN_L

SHIELD

CAN_H

V+

NET

MOD

NODE

DANGER

GND

TX/RX

DeviceNet

(Port 1)

(Replacement

connector part no.

1761-RPL-0000)

RS-232

(Port 2)

Use this write-on

area to mark the

DeviceNet node

Address.

«
...
30
31
32
33
34
...
»

Содержание DeviceNet 1761-NET-DNI






































































































Отзывы:

Нет отзывов