Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 101

Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 37

1761-6.5

DNI Configuration Parameters and Programming Notes

5-3

Input Size

This parameter identifies the size, in words, of the data array that is read
from the controller attached to the DNI’s RS-232 port. The array may
contain up to 16 (16-bit) words of data for DNI Series A (32 words for DNI
Series B) from a contiguous block within the attached controller.

The first byte (byte 0) of the first word contains the status byte and is not
available to the user. A sample of the data array is shown below:

Parameter

Type

Parameter Number

Description Range

Default Value

Series A Series B

I/O

4

1

Input Size

Series A: 1 to 16

Series B: 1 to 32

1

Important:

For DNI Series B, you must also configure the Input Split
Point. See page 5-4.

Word

Input Image

Series A Series B
0

0

Data (8 bits)

Status

1

1

Data Most Significant Byte (MSB) Data Least Significant Byte (LSB)

2

2

Data MSB

Data LSB

3

3

Data MSB

Data LSB

↓

↓

↓

↓

14

30

Data MSB

Data LSB

15

31

Data MSB

Data LSB

Note:

Byte 1 (MSB) of word 0 is available for user data.

Note:

For information on the Status Byte (byte 0), see the Status Byte
section on page 5-23.

«
...
35
36
37
38
39
...
»

Содержание DeviceNet 1761-NET-DNI






































































































Отзывы:

Нет отзывов