manualshive.com logo in svg

Allen-Bradley 1794-IE8H, Руководство пользователя, Страница: 90 / 146

Поделиться
Скачать
Allen-Bradley 1794-IE8H Скачать руководство пользователя страница 90

Publication 1794-UM063A-EN-P - March 2006

6-2

        Troubleshoot the FLEX I/O Analog I/O Modules

1794-OE8H Module

The 1794-OE8H module has one power indicator that is on when power is 
applied to the module, and one status indicator for each input.

Repair

This module is not field repairable. Any attempt to open this module will void 
the warranty. If repair is necessary, return this module to the factory.

Chapter Summary

In this chapter you learned how to troubleshoot the FLEX I/O analog 
modules. Refer to publications 1794-IN108 and 1794-IN109 for complete 
specifications for your module.

Table 6.2 1794-OE8H Status Indicators

Indicator

Color

State

Meaning

Status

Red

On

At power up – Channel 0 indicator lights at powerup until 
all internal diagnostics are checked. After successful 
powerup, the indicator goes off if no fault is present.

After successful powerup – Indicates a critical fault 
(diagnostic failure, etc.)

Blinking (when 
faults are 
enabled, and bit 
set)

Indicates a noncritical channel fault

Yellow

On/blinking

HART device was found on the associated channel (when 
configured)

Power

—

Off

Module not powered

Green

On

Module receiving power

Blinking

No flexbus communication

41442H

A

B

C

   1794- OE8H

Allen-Bradley

B

-

A

OUT 1

OUT 0

OUT 2

PWR

OUT 7

OUT 6

OUT 5

OUT 4

OUT 3

4

8 CHANNEL ANALOG OUTPUT

   I/O

A = Status indicators
B = Insertable labels for writing individual input 
designations
C = Power indicator

Содержание 1794-IE8H



















































































































































Отзывы:

Нет отзывов