Allen-Bradley 1794-IE8H Скачать руководство пользователя страница 118

Страница: 118 / 146

Publication 1794-UM063A-EN-P - March 2006

D-4

FLEX I/O HART Modules Network Messaging

The response from the HART command is reformatted to add this handle and
to add additional status information.

Figure D.1 Response from the HART Command

The six header bytes are added in the front of the HART message response
while the remaining format is unchanged. These six bytes contain the
following information:

•

Response Source

•

Next Assembly

Pointer to assembly for next access.

•

Channel

The actual channel to which actual contents are related.

Status
(6 Bytes)

Start
Character

Address

Command

Byte Count

(Response
Code)

Data

Checksum

Byte

Bit

0…2

3…7

0…7

0…3

2…7

Resp

Source

Next assy index

Handle

Resp
Error

Assy

Access

Error

Chain

Data

Req

allow

Loop

status

avail

Lock

Cold

Start

Res

Value

Meaning

Not valid (default)

Source is HART response

Source is Scan data

CMD 48 response

4…7

Reserved

Value

Meaning

0…7

Channel of I/O module

0x20

FLEX I/O HART module itself

Содержание 1794-IE8H



















































































































































Результаты поиска

Содержание 1794-IE8H

Отзывы:

Allen-Bradley 1794-IE8H, Руководство пользователя, Страница: 118 / 146

Результаты поиска

Содержание 1794-IE8H

Отзывы: