ALLEN & HEATH XONE:4D Скачать руководство пользователя страница 46

Страница: 46 / 48

Allen & Heath

XONE:4D User Guide

USER OPTIONS

Internal Link Options

The Xone:4D offers several internal option settings:



FX1 and FX2 Return Routing

— The FX1 and FX2 Returns are set, by

default, to route to the main LR Mix. Link options allow the return to be

routed through either Filter 1 or Filter 2.



Disabling / Enabling RIAA Preamps

—All channels are fitted with RI-

AA preamplifiers. Link options allow the RIAA preamplifier stage to be

enabled or disabled. When disabled, the Phono input becomes a Line in-

put.



FX2 Pre / Post Fade Assignment

—The FX2 channel send is set, by

default, to pre-fader. Link options allow the channel FX2 send to become

post-fader.

CAUTION :

Refer the above link options to an Allen and Heath approved

service centre only. To reduce the risk of electric shock do not perform any

servicing other than that described in the operating instructions unless you are

qualified to do so.

Replacing the Crossfader

Replacement crossfader Assembly: Allen & Heath Part No. 003-579. Please

contact your Allen and Heath approved service centre to undertake crossfader

replacement.

Содержание XONE:4D

















































Результаты поиска

Содержание XONE:4D

Отзывы:

Похожие инструкции для XONE:4D

Бренды по названию

Популярные бренды

ALLEN & HEATH XONE:4D, Руководство пользователя

Результаты поиска

Содержание XONE:4D

Отзывы:

Похожие инструкции для XONE:4D

Бренды по названию

Популярные бренды