ALLEN & HEATH XONE:4D Скачать руководство пользователя страница 24

Страница: 24 / 48

Allen & Heath

XONE:4D User Guide

Channel Level Control

This control has a range of +/- 10dB either

side of the 0dB centre position. Use it to

adjust the signal level of an audio source to

give a nominal 0dB reading on the channel

meter, with the peak level at or below

+6dB. Turn

LEVEL

down if the +10 peak

meter starts flashing.

Channel Equalizer/Isolator

The Xone:4D is equipped with a very

powerful 3 band EQ stage providing a

controlled +6dB of boost when fully

clockwise but full isolation (cut) of each

band for dramatic effect when fully anti-

clockwise. Centre frequencies are set at:

HF = 10kHz (high frequency, treble)

MF = 1.2kHz (mid frequency)

LF = 120Hz (low frequency, bass)

MIXER SECTION — CHANNEL INPUT

Filter/Crossfade Assignment

The channel signal can be routed directly

to the main mix or via either of the two

filter/crossfade paths. Note that the

crossfade affects the filter path only.
Set the 3-position switch to its mid

position to route the signal direct to the

mix, or to its left or right positions to

route the signal to filter-1/crossfade-X or

filter-2/crossfade-Y respectively.
To enable the crossfader check that the

XFADE ON

switch above the filter1

controls is pressed.

Cue Switch

Press the cue switch to listen to the channel

pre-fade signal in the headphones and see its

level on the main meters. The LED

indicator ring around the switch lights up

when selected. The big red

CUE ACTIVE

indicator also lights to warn that you are

monitoring the channel signal rather than

the main mix.
Press the switch to deselect cue. The

switches are interlocked; pressing another

one turns off the previous selection.

Содержание XONE:4D

















































Результаты поиска

Содержание XONE:4D

Отзывы:

Похожие инструкции для XONE:4D

Бренды по названию

Популярные бренды

ALLEN & HEATH XONE:4D, Руководство пользователя

Результаты поиска

Содержание XONE:4D

Отзывы:

Похожие инструкции для XONE:4D

Бренды по названию

Популярные бренды