ALLEN & HEATH XONE:4D Скачать руководство пользователя страница 39

Страница: 39 / 48

Allen & Heath

XONE:4D User Guide

MIDI CONTROL SECTION

MIDI Messages

The diagram below shows which controls are associated with MIDI CC (continuous controller)

and note on/off messages. These controls send the MIDI messages shown when operated. The

switch light ring indicators (except for start/stop and tap tempo) may be turned on or off by

incoming MIDI messages.

MIDI Channel Number and Map

To change the MIDI map and channel number, please refer to the

MIDI CHANNEL, MAP AND

LIGHT PIPE SETUP

sections on pages 11 and 12.

MIDI Shift Mode

All of the controls on the Xone:4D (with the exception of the crossfader, can be mapped a

second time using the MIDI shift mode. To enter

MIDI SHIFT MODE

, hold down the encoder

above the jog wheel on the left MIDI pod for approximately half a second. The BPM display will

show

SFT

when the console is in shift mode. A fader pick up algorithm has been written into

the software to ensure seamless integration between the two MIDI layers. In shift mode, the

channel MIDI messages are sent on the default MIDI channel minus 1—i.e. if you are transmitting

on MIDI channel 16 then shift mode will transmit on channel 15. The only exception is if the

default channel is channel 1 then the shift mode will transmit on channel 2.

CC32 CC33 CC34 CC35

F6 F#6 G6 G#6 A6 Bb6 B6 C7

CC9 CC11 CC13 CC15

CC8 CC10 CC12 CC14

CC19 CC18 CC17 CC16

Eb0

Eb1

F#0

G#1

C#2

Bb0

CC36

CC37

Bb-1

A-1

B-1

C#0

CC40 CC41 CC42 CC43

Bb2

Bb3

C#7 D7 Eb7 E7 F7 F#7 G7 G#7

CC21 CC23 CC25 CC27

CC20 CC22 CC24 CC26

CC31 CC30 CC29 CC28

C#4

C#3

G#4

F#3

Eb3

G#3

CC44

CC45

F#2

C#5

Eb5

Eb6

C#6

CC7

CC5

Bb5

CC6

G#5

FOOTSWITCH CC4 - DOWN = 127, UP = 0

JOYSTICK X = CC3 - LEFT = 127, RIGHT = 0 Y = CC1 - UP = 127, DOWN = 0 FINGER BUTTON = C#-1 THUMB BUTTON = D-1

MAP 1

MAP 2

MAP 1

MAP 2

Bb4

F#4

G#0

Bb1

Содержание XONE:4D

















































Результаты поиска

Содержание XONE:4D

Отзывы:

Похожие инструкции для XONE:4D

Бренды по названию

Популярные бренды

ALLEN & HEATH XONE:4D, Руководство пользователя

Результаты поиска

Содержание XONE:4D

Отзывы:

Похожие инструкции для XONE:4D

Бренды по названию

Популярные бренды