ALFAtron ALF-MUH88E Скачать руководство пользователя

Страница: 39 / 44

ALFATRON ALF-MUH88E

EDID management does
not work normally

The HDMI cable is broken
at the output end.

Change for another HDMI
cable which is in good
working condition.

There is a blank screen on
the display when switching

The display does not
support the resolution of
the video source.

Switch again.

Manage  the  EDID  data
manually  to  make  the
resolution  of  the  video
source

automatically

compliant with the output
resolution.

Cannot control the device

by control device (e.g. a

PC) through RS232 port

Wrong connection

Check to ensure the

connection between the

control device and the unit

Wrong RS232

communication parameters

Type in correct RS232

communication

parameters: Baud

rate:9600; Data bit: 8; Stop

bit: 1; Parity bit: none

Broken RS232 port

Send it to authorized

dealer for checking.

Static becomes stronger

when connecting the video

connectors

Bad grounding

Check the grounding and

make sure it is connected

well.

Cannot control the device

by RS232 / IR remote / front

panel buttons

The device has already

been broken.

Send it to authorized

dealer for repairing.

If your problem persists after following the above troubleshooting steps, seek further
help from authorized dealer or our technical support.

Содержание ALF-MUH88E













































Результаты поиска

Содержание ALF-MUH88E

Отзывы:

Похожие инструкции для ALF-MUH88E

Бренды по названию

Популярные бренды

ALFAtron ALF-MUH88E, Руководство пользователя

Результаты поиска

Содержание ALF-MUH88E

Отзывы:

Похожие инструкции для ALF-MUH88E

Бренды по названию

Популярные бренды