ALFAtron ALF-MUH88E Скачать руководство пользователя

Страница: 10 / 44

ALFATRON ALF-MUH88E

2.2 HDBaseT Receiver

No.

Name

Description

①

Power
Indicator



OFF

: No power;



RED:

DC power present (PoC).

②

DC 12V

Connect with power supply (PoC).

③

HDBaseT
IN

The RJ45 socket has two LED status indicators. Plug in the Pre-
installed CAT cable in to the HDBT RJ45 socket.



HDCP

: HDCP compliant indicator



OFF: No HDMI traffic (no picture)



GREEN: Signals with HDCP.



Blinking GREEN: Signal without HDCP



LINK

: HDBT Link status indicator.



OFF: No Link



YELLOW:Link Successful



Blinking YELLOW: Link Error

④

HDMI OUT Connect to HDMI display.

⑤

IR IN

Plug in the IR receiver, this will receive the IR signals from the RCU
and send through to the Matrix Switcher and then control the
desired source.

⑥

IR OUT

Plug in the IR emitter and attached to the fornt of the display, this
will send the IR signals form the Matrix Switcher to control the
display which is connected to the HDMI OUT port.

HDMI OUT

IR IN

IR OUT

LINK

HDCP

DC 12V

1 2

Содержание ALF-MUH88E













































Результаты поиска

Содержание ALF-MUH88E

Отзывы:

Похожие инструкции для ALF-MUH88E

Бренды по названию

Популярные бренды

ALFAtron ALF-MUH88E, Руководство пользователя

Результаты поиска

Содержание ALF-MUH88E

Отзывы:

Похожие инструкции для ALF-MUH88E

Бренды по названию

Популярные бренды