background image

7

if necessary to protect the system from flooding, heavy snow etc. 

2.

  Prepare  one  or  more  conduits  for  the  electrical  cables  before  pour  concrete.  Remember  that  cable 

conduits have to pass through the hole in the base plate.

3. 

Pour concrete and before it starts to harden, check that it is parallel to the gate leaf and perfectly level.

4.

 The four anchor bolts must be set into the concrete when it is poured, make sure the position of anchor 

bolts  was  placed according  to  the  position  of  mounting holes  on  the  base  plate  before  concrete  become 

harden.

5. 

Mount  the  base  plate  to  the  concrete  Pad.  It's  only  temporary  installation.  Further  adjustment  will  be 

required when install the chain.

6. 

Mount the chain box to the base plate by using screws and washers, don’

t make the four screws too tight.

Manual Operation 

The opener should be put in the manual (emergency release) position before fitting the rack, installing the 

opener and limit switch. The process is as follows:

1) Take off the rubber stopple.

2) Insert the Release Key

provided

and turn it in counter-clockwise 180° to disengage the clutch between 

the gear shaft and power output. Now the opener is in the manual operation.

             

Installation of chain and chain brackets

1. Chain Brackets

1).  Please  refer  to  below  chain  brackets  figure, 

which shows “U” bolt,    “L” bracket and chain bolt.

Use the “U” bolts (square or round)  to  attach  the 

chain brackets to gate frame.

2). If Both the square bolts and round bolts are not 

fit for the gate frame, use the appropriate bolts to 

attach the chain brackets to gate frame.

2. How to install the chain

1).  Place  the  chain  around  the  top  of  the  idler 

wheels and under the drive sprocket in chain box.

2). Connect a chain bolt to one end of chain from 

chain  box  by  using  master  link.  Then  insert  the  chain  bolt  to  the  L  bracket  and  fix  them  each  other  by 

Содержание AC 1500

















Отзывы: