background image

14

Troubleshooting

Have a multimeter to check voltage and continuity. Use caution when checking high voltage terminals.

Maintenance

Every six months check the following items for proper operation of the unit.

* Lubricate shafts and sprockets.

* Keep operator clean at all times.

* Check and tighten anchors bolts.

* Check for loose or corroded wire

* Ensure the operator is well earthed, and correctly terminated.

* Always check the Stop/Reverse in case of obstruction function when performing any maintenance. If

this  function can’

t be made operable, remove this operator from service until the cause of the

malfunction is identified and corrected.

Symptom

Possible Solution(s)

The  remote  control 

does  not  emit  any 

single

Check the batteries are exhausted, replace them if necessary.

The  operator  doesn’

run.

1. Make sure that the power cord is properly plugged into the mains outlet.

2.  Check  the  fuse  is  blown  in  the  control  board;  if  necessary,  identify  the 

reason for the failure and then replace a new one. 

3.  Make  sure  the  photocell  beam  is  not  blocked  if  the  photocell  is  used.

Check the terminal 11 should be shorted with terminal 12 by a jumper wire. 

Please reset this jumper wire if it is loss. 

The gate starts but it is 

immediately  stop  or 

reverse

1. The selected force is too small to move the gate. Turn the Potentiometer

clock-wise to increase the force.

2. Disconnect the gate from the gate operator and check that the gate slides 

freely without any binding.

Содержание AC 1500

















Отзывы: