Alcatel-Lucent 9927 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 247

Alcatel-Lucent 9927 Скачать руководство пользователя страница 74

Environmental requirements

Environmental requirements for outdoor installations

Outdoor cabinet installations are exposed to variations in temperature, humidity, and
ventilation.

The 9927 Distributed Base Station cabinet has been weather-hardened. When equipped
with a heat exchanger, the cabinet will operate under the conditions described in the table
below.

Condition

Specification

Operating
temperature

-40 °C to +46 °C (-40 °F to +115 °F)

Extended operating
temperature

-40 °C to 50 °C (-40 °F to 122 °F)

Relative humidity

5 to 100% (non-condensing but not to exceed 0.024 kg water/kg of dry
air)

Enclosure rating

Type 3R (NEMA)

IP35 (IEC 60529)

Acoustic noise
suppression

65 dBA at 25 °C (77 °F) and sea level

Operating altitude

-60.96 to 1798 m (-200 to 5,900 ft.) above sea level

Extended operating
altitude

-60.96 to 3048 m (-200 to 10,000 ft.). An operating temperature
de-rating of 1 °C per 1000 feet above 6000 feet is allowed

Wind driven rain

Refer to Telcordia GR-487-CORE

Dust and water
ingress

Refer to Telcordia GR-487-CORE

Bullet resistance

Refer to Telcordia GR-487-CORE

Wind resistance

Refer to Telcordia GR-487-CORE

Storage requirements

Refer to Telcordia GR-63-CORE, Section 4.1.1

Minimum installation temperatures

Insulation on power cables tends to crack when handled at extremely cold temperatures.
Minimum installation temperatures have been established for this reason.

The following wire insulation types are affected :

•

Class B: THHN type insulation (T90 NYLON type insulation in Canada).

Basic site preparation requirements and footprints for 9927
Distributed Base Station outdoor cabinet
Site requirements for 9927 Distributed Base Station
Outdoor cabinet

Environmental requirements

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

5-4

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

9927 Dist BTS Outdoor

401-703-516

Issue 1

March 2012

«
...
72
73
74
75
76
...
»

Содержание 9927
























































































































































































































































Отзывы:

Нет отзывов