Albasca MK-5800 Скачать руководство пользователя страница 49

Страница: 49 / 128

Enter Setup

** Exit Setup

Transmit Check Digit

EAN-8 is 8 digits in length with the last one as its check digit used to verify the integrity of the data.

Transmit EAN-8 Check Digit

Do Not Transmit EAN-8 Check Digit

Add-On Code

An EAN-8 barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the

examples below, the part surrounded by blue dotted line is an EAN-8 barcode while the part circled by

red dotted line is add-on code.

Enable 2-Digit Add-On Code

Disable 2-Digit Add-On Code

Enable 5-Digit Add-On Code

Disable 5-Digit Add-On Code

Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code:

The scanner decodes a mix of EAN-8

barcodes with and without 2-digit/5-digit add-on codes.

Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code:

The scanner decodes EAN-8 and

ignores the add-on code when presented with an EAN-8 plus add-on barcode. It can also decode EAN-8

barcodes without add-on codes.

Содержание MK-5800

































































































































Результаты поиска

Содержание MK-5800

Отзывы:

Albasca MK-5800, Руководство по настройке, Страница: 49 / 128

Результаты поиска

Содержание MK-5800

Отзывы: