Albasca MK-5800 Скачать руководство пользователя страница 42

Страница: 42 / 128

Enter Setup

31 *

* Exit Setup

Set Terminating Character Suffix

The engine provides a shortcut for setting the terminating character suffix to CR (0x0D) or CRLF

(0x0D,0x0A) and enabling it by scanning the appropriate barcode below.

Terminating Character CR (0x0D)

Terminating Character CRLF (0x0D,0x0A)

To set a terminating character suffix, scan the

Set Terminating Character Suffix

barcode and the

numeric barcodes representing the hexadecimal value of a desired terminating character and then scan

the

Save

barcode. Refer to

Appendix 3: ASCII Table

for hexadecimal values of terminating characters.

Note:

A terminating character suffix cannot exceed 7 characters.

Set Terminating Character Suffix

Example: Set the terminating character suffix to 0x0D

1. Scan the

Enter Setup

barcode.

2. Scan the

Set Terminating Character Suffix

barcode.

3. Scan the numeric

barcodes “0” and “D”.

4. Scan the

Save

barcode.

5. Scan the

Exit Setup

barcode.

Содержание MK-5800

































































































































Результаты поиска

Содержание MK-5800

Отзывы:

Albasca MK-5800, Руководство по настройке, Страница: 42 / 128

Результаты поиска

Содержание MK-5800

Отзывы: