Albasca MK-5800 Скачать руководство пользователя страница 35

Страница: 35 / 128

Enter Setup

** Exit Setup

Custom Prefix

Enable/Disable Custom Prefix

If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot

exceed 11 characters.

Enable Custom Prefix

** Disable Custom Prefix

Set Custom Prefix

To set a custom prefix, scan the

Set Custom Prefix

barcode and the numeric barcodes representing the

hexadecimal values of a desired prefix and then scan the

Save

barcode. Refer to

Appendix 3: ASCII

Table

for hexadecimal values of characters.

Note:

A custom prefix cannot exceed 11 characters.

Set Custom Prefix

Example: Set the custom prefix to

“CODE”

1. Check the hex values of

“CODE” in the ASCII Table. (“CODE”: 43, 4F, 44, 45)

2. Scan the

Enter Setup

barcode.

3. Scan the

Set Custom Prefix

barcode.

4. Scan the numeric

barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5”.

5. Scan the

Save

barcode.

6. Scan the

Exit Setup

barcode.

Содержание MK-5800

































































































































Результаты поиска

Содержание MK-5800

Отзывы:

Albasca MK-5800, Руководство по настройке, Страница: 35 / 128

Результаты поиска

Содержание MK-5800

Отзывы: