Albasca MK-5800 Скачать руководство пользователя страница 16

Страница: 16 / 128

Enter Setup

5 *

* Exit Setup

Timeout between Decodes (Same Barcode)

Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode in a given

period of time.

To enable/disable the Timeout between Decodes (Same Barcode), scan the appropriate barcode below.

Enable Timeout between Decodes (Same Barcode):

Do not allow the engine to re-read same barcode

before the timeout between decodes (same barcode) expires.

Disable Timeout between Decodes (Same Barcode):

Allow the engine to re-read same barcode.

The following parameter sets the timeout between decodes for same barcode. It is programmable in 1ms

increments from 0ms to 65,535ms. The default setting is 1,500ms.

To learn how to program this parameter, see

Appendix 4

Timeout between Decodes (Same Barcode)

** Disable Timeout between Decodes (Same Barcode)

Enable Timeout between Decodes (Same Barcode)

Содержание MK-5800

































































































































Результаты поиска

Содержание MK-5800

Отзывы:

Albasca MK-5800, Руководство по настройке, Страница: 16 / 128

Результаты поиска

Содержание MK-5800

Отзывы: