AL-MEISTER ALM3222 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 52

background image

AL-MEISTER ALM3222 Instruction Manual <Rev.2>

Page

50

of

52

new film rolls. CAUTION: The
lamination rollers get very hot.

●PAPER STUCK

Paper is stuck in feeder
section,

cutter

(lamination)

section or trimmer section.
The section where the paper is
stuck is indicated as an error
number on LCD as follows:

1 Feeder section

2 Lamination section

3 Trimmer section

Open  the  feeder  cover  and
trimmer  cover.  Remove  all  the
stuck  sheets  in  the  machine.
Follow  the  instruction  for  the
problem :
●Laminated

sheet

is

not

discharged,

page.34.

Press

RESET  button  to clear error.  In
case  the  error  is  not  solved,
switch off  and contact  your dealer
or the Drylam Tech-Line.

Lamination scrap is stuck in
trimmer section.

Open trimmer cover. Remove all
the

lamination scraps. Press

RESET button to clear the error.

Be careful that your fingers do not
get cut.

●FILM ERROR

Check if the sealed film roll is
set to the lower socket.

Be sure the sealed film roll is set
to the lower position

●COVER OPEN

Close the cover. Press RESET
button.

●OVERHEAT

Turn off  the  power.  Then  turn  on
the  power. The problem  will  be
solved  in most  cases,  If  the
problem  is  not solved,  contact
your  dealer  or the Drylam Tech-
Line.

●TEMP. SENSOR BREAK

Turn off the power. Contact your
dealer or the Drylam Tech-Line.

Do not dismantle.

●TEMP. SENSOR SHORT
CIRCUIT

Turn off the power. Contact your
dealer or the Drylam Tech-Line.

Do not dismantle.

●LAMINATION

MOTOR

ERROR

Turn off the power. The problem
will be solved in most cases. If the
problem occurs frequently, contact
your dealer or the Drylam Tech-
Line.

●Other Errors than the
above mentioned.

Switch off and contact your dealer
or the Drylam Tech-Line

Do not

dismantle.

●CUTTER DOES NOT
CUT WELL

Contact your dealer or the Drylam
Tech-Line.

Do not dismantle.

●TRIMMER DOES NOT
CUT WELL

Lamination scrap is stuck in
trimmer section.

Open Trimmer Cover. Remove all
the lamination scrap.

Be careful

that your fingers do not get cut.

●LEFT

AND

RIGHT

MARGIN IS NOT EQUAL

Check the Feed Tray.

Adjust the feed adjustment knob.

Check

if the

trimmer Adjust the trimmer adjustment

«
...
48
49
50
51
52
»

Содержание ALM3222





















































Отзывы:

Нет отзывов

Похожие инструкции для ALM3222

Бренд: Olympia Страницы: 150

Бренд: ABC Office Страницы: 34

Бренд: Fellowes Страницы: 11

Бренд: Fellowes Страницы: 12

Бренд: Fellowes Страницы: 58

Бренд: Fellowes Страницы: 58

Бренд: Fellowes Страницы: 79

Бренд: Peach Страницы: 20

Бренд: 3M Страницы: 2

Бренд: Easymount Страницы: 9

Бренд: Xyron Страницы: 6

Бренд: UNITED OFFICE Страницы: 51

Бренд: UNITED OFFICE Страницы: 63

Бренд: UNITED OFFICE Страницы: 115

PROTOPIC III-540

Бренд: GMP Страницы: 48

PROTOPIC AUTO-540 HS

Бренд: GMP Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды