AL-MEISTER ALM3222 Скачать руководство пользователя страница 3

Страница: 3 / 52

AL-MEISTER ALM3222 Instruction Manual <Rev.2>

Page

IMPORTANT

The following safety precautions must be observed for your safety during the operation of this product.
Please read the cautions and warnings carefully. Please keep this manual and refer to it whenever
necessary.

General Caution

Electric Shock

Indicates the potential for electric shocks.

Tangling Warning

Indicates possible injuries caused by tangling in a rotating machine

part.

Amputation Warning

Indicates possible serious injuries such as finger amputation.

Heat Warning

Indicates the potential for injuries caused by extreme heat.

Don’t Do

Indicates unspecified acts that are forbidden.

Unplug immediately

Indicates a dangerous situation. Unplug the ALM3222 from the

wall outlet and call for service.

These two different words are used on the machine according to the level of danger.

WARNING

In the case of incorrect use, there can be serious injury.

CAUTION

Injury to the operator or damage to equipment possible. There can also be a

machine malfunction.

Содержание ALM3222





















































Результаты поиска

Содержание ALM3222

Отзывы:

Похожие инструкции для ALM3222

Бренды по названию

Популярные бренды

AL-MEISTER ALM3222, Инструкция по эксплуатации

Результаты поиска

Содержание ALM3222

Отзывы:

Похожие инструкции для ALM3222

Бренды по названию

Популярные бренды