Akw 25450 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 24

background image

Technical Support:

01905 560 219

23

Order:

01905 823 299

|

orders.akw-ltd.co.uk

23

aC

TIV

aT

e W

aRR

an

TY

activate Warranty

3. Visit Online

akw-ltd.co.uk/online-warranty-submission

2. Scan using your Smart Device

Select 1 of 3 ways to activate your warranty

1. Warranty Card

fill and complete warranty card and post

using the envelope supplied

ACTIVATE WARRANTY

These instructions are provided to advise the minimum standards of installation and recommends what the best practice for the installation is.

Due to the very wide variability of possible installation conditions, aKW cannot provide all circumstances for the installation. aKW cannot accept any liability in connection with this information or its

use. This information is provided on the condition that the person receiving it shall make his/her own tests to determine the suitability for the particular purpose. failure to install this aKW product in

accordance with supplied instructions or the making of unauthorised modifications will invalidate any warranty and may affect product safety.

none of the foregoing affects your statutory rights.

«
...
21
22
23
24
»

Содержание 25450

























Отзывы:

Нет отзывов

Похожие инструкции для 25450

Бренд: Sanela Страницы: 2

Metropol 13159180

Бренд: Hans Grohe Страницы: 24

Talis S 32420000

Бренд: Hans Grohe Страницы: 232

Бренд: Hans Grohe Страницы: 76

AXOR Starck 10020 Series

Бренд: Hans Grohe Страницы: 16

Axor Starch 28491000

Бренд: Hans Grohe Страницы: 24

Axor Starck 10010 Series

Бренд: Hans Grohe Страницы: 174

Focus E 31780000

Бренд: Hans Grohe Страницы: 36

Focus Eco 31821000

Бренд: Hans Grohe Страницы: 44

Бренд: Hans Grohe Страницы: 8

Бренд: Hans Grohe Страницы: 2

Focus 100 31509000

Бренд: Hans Grohe Страницы: 40

Rainfinity 250 1jet EcoSmart 26227 Series

Бренд: Hans Grohe Страницы: 48

Rainfinity 500 1jet 26243 Series

Бренд: Hans Grohe Страницы: 24

Raindance Select E 360 Showerpipe EcoSmart...

Бренд: Hans Grohe Страницы: 16

Raindance Showerpipe 27146 1 Series

Бренд: Hans Grohe Страницы: 28

Raindance Select S 240 2jet Showerpipe 27129 1...

Бренд: Hans Grohe Страницы: 32

Raindance Select S 240 2jet 26470000

Бренд: Hans Grohe Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды