background image

Technical Support: 

01905 560 219

3

Order: 

01905 823 299 

 

|

  orders.akw-ltd.co.uk

3

bo

x C

on

Ten

TS

 &

 S

Pe

C

If

IC

aTI

on

S

Box Contents & Specifications

1x 

3x 

Stock Code: 25470

AKW M11 DigiPump

 

Supply: 230V aC 50Hz 100W
Ingress Protection: IP45
Duty Cycle: 50% Max 30 Mins. on
for use with electric & mixer showers.
Pump and controller enclosed in one unit.
Max flow rate: 11 litres Per Minute (lPM).
non-handed, selectable inlet/outlet direction.
Max Head: 1.0m (39in)
Max lift: 0.5m (20in)

1x 

3x 

2x 

22mm

2x 

22mm

Supply: 230V aC 50Hz 100W   

   

Ingress Protection: IP45
Duty Cycle: 50% Max 30 Mins. on 

 

for use with electric & mixer showers.
Pump and controller enclosed in one unit.
Max flow rate: 17 litres Per Minute (lPM)
non-handed, selectable inlet/outlet direction.
Max Head: 1.0m (39in)
Max lift: 0.5m (20in)

Supply: 230V aC 50Hz 100W   

   

Ingress Protection: IP45
Duty Cycle: 50% Max 30 Mins. on 

 

for use with electric & mixer showers.
Pump and controller enclosed in one unit.
Max flow rate: 20 litres Per Minute (lPM)
non-handed, selectable inlet/outlet direction.
Max Head: 1.0m (39in)
Max lift: 0.5m (20in)

Confirm you have all the correct parts required. Ensure the volume of water from the shower does not exceed the 

pumps drainage capacity. note: Increased Head/lift conditions will affect the pump’s performance.

AKW M20 DigiPump

1x 

3x 

2x 

22mm

3x 

1x  15mm               

1x  15mm               

1x            

1x 22mm

1x 22mm

1x

2x 

MI

N

100mm MIN

*

HEAD

LIFT

*

*

*

MI

N

100mm MIN

*

HEAD

LIFT

*

*

*

3x 

1x

1x

2x 

MI

N

100mm MIN

*

HEAD

LIFT

*

*

*

MI

N

100mm MIN

*

HEAD

LIFT

*

*

*

3x 

1x

1x

2x 

MI

N

100mm MIN

*

HEAD

LIFT

*

*

*

MI

N

100mm MIN

*

HEAD

LIFT

*

*

*

2x 

22mm

Contents

Stock Code: 25450

AKW M17 DigiPump

Stock Code: 25460

Содержание 25450

























Отзывы: