background image

1652H302 Ed.03

10

Cold regulation

Solenoid control (COOL Relay)

Cold  production  is  regulated  by  means  of  opening  / 
closing the solenoid valve.
When  the  temperature  in  probe  S1  reaches  the  set 
point (

SP

) value plus the probe's differential (

C1

), the 

solenoid  opens  and  causes  the  temperature  to  drop. 
Once the set point (

SP

) value is reached, the solenoid 

closes.

Compressor control (Relay AUX 1)

With Pump Down (

Inl:

 2, 5, 7, 9, 12)

Requires  the  connection  of  a  low  pressure 
switch in digital input 1.

When  the  temperature  in  probe  S1  reaches  the  set 
point (

SP

) value plus the probe’s differential (

C1

), the 

solenoid opens, causing the pressure in the evaporator 
to  increase  and,  therefore,  the  low  pressure  switch 
deactivates and the compressor starts up. 
Once the set point (

SP

) value is reached, the solenoid 

closes,  causing  the  pressure  in  the  evaporator  to 
decrease,  triggering  the  low  pressure  switch  and 
stopping the compressor.
For further details of the process, see the next page.

Without Pump Down (

Inl:

 3, 6, 8, 10, 13)

The compressor operates simultaneously with the solenoid valve, starting up when the latter opens and stopping 
when it closes.

Operation in the event of a fault in probe S1

If  probe  S1  fails  (fault,  disconnection,  etc.  ),  compressor  behaviour  will  depend  on  parameter 

C6

,  with  one  of  3 

options available:

C6=0:

 The compressor is stopped until probe S1 begins to operate again.

C6=1:

 The compressor is started-up until probe S1 begins to operate again

C6=2:

 The  compressor  operates  in  line  with  the  average  operation  during  the  24  hours  prior  to  the  error, 

taking into account the number of start-ups and stops and the average time in each state (stop-start). 
If 24 hours have not elapsed without a probe error, the device moves to 

C6=3

 mode.

C6=3:

 C6=3: The compressor operates in line with the times programmed in 

C7

 (ON) and 

C8

 (OFF).

SP+C1

SP+C1

SP

SP

Solenoid

Solenoid

Low 

pressure

switch

Compressor

Compressor

ON

ON

ON

ON

ON

ON

C7

C7

C8

S1

S1

Содержание AKO-16520

































Отзывы: