Airspan Air4G Скачать руководство пользователя страница 27

Страница: 27 / 73

Air4G Installation Guide

Page 27

Commercial in Confidence

UGD-D00229 Rev B

Air4G Base
Station parts

Consisting of

Filter (Cavity
filter) Kit (for
2.3 GHz variant

only

) (U.S.A. –

WCS market
only)

2 x Cavity Filters – 141-00-148

4 x antenna cables – 689-000-47

4 x stainless steel pole bands for pole mounting

External
Duplexer Kit
(for some FDD
variants

only

) –

Supplied with
Air4G

1 x External Duplexer (with pre-assembled mounting bracket)

2 x 50-215 mm stainless steel pole bands for pole mounting

4 x RF jumper cables (1.5 m each) for connecting 2 x (Tx + Rx) between the
Air4G antenna ports and the Duplexer

RF cable
(ordered
separately)

2 x antenna cables for connecting the antennas to the Air4G / External
Duplexer.

The following table displays the parts contained in the included GPS Kit and when the parts are
required per configuration. See

GPS Antenna Assembly



= required when applicable for this configuration

X = not required in this configuration

Table 11 - GPS Kit Contents

Part

Description

Air4G

Air4Gp

Air4Gs

Image

Ext. Int.

GPS Antenna 1 x GPS Antenna. An active GPS

antenna which, with the appropriate
mounting bracket is used with the
BS for network synchronization.



80cm GPS
Cable - RG58
TNC-TNC

See

Optional

Cables

For mounting the GPS directly to
the top of the BS. Should be used in
conjunction with the BS GPS
antenna mounting bracket pre-
assembled on the BS. P/N CBL-
GPS-TNC-0.8-1





Remote GPS
Antenna
Mounting
Bracket

Used in conjunction with the long
GPS Cable - when mounting GPS
remotely.

(see optional cables below)



Lightning/Surge
protector

Surge Protector designed to protect
from lightning strikes.

An additional mounting bracket
included in the packaging is not
required for use.





Warning:

Surge protection requires proper grounding to provide

proper protection against surge damage due to lightning or other surge
events.

Содержание Air4G










































































Результаты поиска

Содержание Air4G

Отзывы:

Airspan Air4G, Руководство по установке, Страница: 27 / 73

Результаты поиска

Содержание Air4G

Отзывы: