Airspan Air4G Скачать руководство пользователя страница 16

Страница: 16 / 73

Air4G Installation Guide

Page 16

Commercial in Confidence

UGD-D00229 Rev B

90° Dual Slant X-Polar – mounting
kit (50 > 115 mm) included

3.3-3.8 GHz

17.0 dBi

SEC90X-3.5-RC-1

Omni Reg Compl Vertical Sector

3.3 – 3.5 GHz

10.0 dBi

OMNIV-3.4-RC-2

Table 7 - 5.x GHz Antenna Types - Technical

Type

Frequency range

Gain

Part number

Dual Slant ± 45 degrees 90 Sector

4.9 - 6.1 GHz

16.5dBi

SEC90X-5.X-RC-1

Air4G Antenna Usage

Air4G has four (4) RF ports that can be connected to either:



A single four-port antenna



Two dual-port antennas



Four single-port antennas

Note:

Appropriate mounting kit (included) for the dual and quad port

antennas are required.

•

Quad port cross polarized (X-Pol) antenna with four (4) ports – connected via 4
RF jumper cables to Air4G.

•

Dual slant cross polarized (X-Pol) antenna with two (2) ports - connected via 2 RF
jumper cables to Air4G.

•

Omni antennas – for 360 degree coverage using a single Air4G - requires an
Omni antenna for each receiver – 2 or 4 Omni antennas.

Note:

The Omni antennas must be separated – with at least one meter

separation from each other (in 2.X and in 3.X GHz). Additional separation for
700, 800 MHz and 1.8 GHz.

•

Fixed tilt dual/quad port antennas (where the tilt is set by the way the mounting kit
is installed).

Note:

Required mounting kits for fixed tilt dual/quad port antennas are

included.

•

Manual Electric Tilt (MET) dual/quad antennas - a variable tilt antenna available
for mounting directly on the Air4G with no need for physical tilting of the antenna.

The following table describes different antenna arrays when using either two (2) receivers or four
(4) receivers:

Table 8 - Antenna arrays

Frequency Band

# of Receivers

Sector

Antenna Type

# of Antennas

700 MHz

60º

698 - 806 MHz 60

13.5 dBi

Dual X-Polar

700 MHz

60º

698 - 806 MHz 60º 13.5 dBi
Dual X-Polar

2.3 GHz

65º

2.3-2.7 GHz 60º Dual Slant X-
Polar

Содержание Air4G










































































Результаты поиска

Содержание Air4G

Отзывы:

Airspan Air4G, Руководство по установке, Страница: 16 / 73

Результаты поиска

Содержание Air4G

Отзывы: