Airspan Air4G Скачать руководство пользователя страница 26

Страница: 26 / 73

Air4G Installation Guide

Page 26

Commercial in Confidence

UGD-D00229 Rev B

Air4G Base
Station parts

Consisting of

Note:

The Sunshield brackets are only applicable for antennas that utilize

Mechanical Electric Tilt (MET). i.e. – Argus-SSPX310F.

Warning:

A Sunshield is mandatory for temperatures of above 45°.

1 x Air4G Wall
mounting kit

Air4G-W24-WMK-3 – wall mounting kit with accessories included

Pole (& Wall)
Mounting Kit for
pole with 60-
120 mm
diameter, No
Tilt
(ordered
separately)

Air4G-W24-PMK-60-120-1 – Pole (with Wall) mounting kit for poles with
diameters 60-120 mm – including fixing accessories.

Pole (& Wall)
Mounting Kit for
pole with 120-
230 mm
diameter, No
Tilt

(ordered
separately)

Air4G-W24-PMK-120-230-3

Pole (with Wall) mounting kit for poles with

diameters 120-230 mm - including fixing accessories.

1 x earth kit

1 x M5 screws

1 x M5 washers

1 x M5 spring washers

Alternative: SEMS screw (includes 2 washers)

AC/DC Power
Supply (PS)

Indoor power converter for 5.x GHz, 2.x GHz, 700 MHz

Indoor or Outdoor power converter for 3.xGHz

Type-IC DC
Power Cable

Available either in - 10, 15 or 30 meter lengths. Additional lengths available.

ODC Twin
Fiber Cable
(Multimode)
(optional)
(ordered
separately)

Available either in - 10, 15, 30, 50, 75 or 100 meter lengths.

Note:

Maximum up to 500 meters as this is a multimode

interface.

Multimode fiber
pigtail cable
(not included)
(optional)
(ordered
separately)

Multimode fiber pigtail cable – ODC - LC connector. Terminates the outdoor
fiber cable and provides an indoor LC connector. 2 meter length.

Grounding
Cable
(required) (not
included)

Circular earth braid, 120A current (16 mm²), jacketed or not with cable size =
AWG 4 – 6 with lug (terminal) on enclosure side with hole M6

Содержание Air4G










































































Результаты поиска

Содержание Air4G

Отзывы:

Airspan Air4G, Руководство по установке, Страница: 26 / 73

Результаты поиска

Содержание Air4G

Отзывы: