Airspan 605-0000-742 Скачать руководство пользователя страница 66

Страница: 66 / 83

605-0000-742_MicroMAX_Hardware_Installation_Rev_G

CONNECTING THIRD-PARTY EXTERNAL ANTENNAS

This section describes the procedures for connecting third-party external radio and Global

Positioning System (GPS) antennas to the BSR and BSDU, respectively. The implementation of

these antennas depends on the BSR model (with respect to radio antennas) and the need for

synchronization of the system (with respect to GPS antennas).

Connecting Third Party External Antennas

The MicroMAX BSR model without a built-in antenna provides an N-type port for connecting a third-

party external antenna. The addition of an external antenna allows greater RF sector coverage than
the standard MicroMAX BSR built-in antenna model.

Warning:

Before connecting the external antenna, ensure that the MicroMAX is not

connected to the power source.

Warning:

Before powering on the MicroMAX, ensure that some type of equipment such

as an antenna or an RF attenuator is connected to the N-type receptacle. This eliminates the
risk of irreversibly damaging the MicroMAX device.

Warning:

It is the responsibility of the person installing the MicroMAX to ensure that

only those antennas certified with the product are used. The use of any antenna other than

those certified with the product is expressly forbidden.

Warning:

The external antenna must not be co-located or operating in conjunction

with any other antenna or transmitter.

Warning:

The MicroMAX and external antenna should be installed ONLY by

experienced installation professionals who are familiar with the local building and safety codes

and are licensed by the appropriate government authorities.

Note:

The MicroMAX model that provides an N-type connector for attaching a third-party

external antenna does not contain an internal, built-in antenna.

The following lists the cable setup for attaching the external antenna:

Cable: RF coaxial

Connector: N-type male

To connect a third-party external antenna to the MicroMAX:

Connect the N-type male connector of the third-party antenna to the N-type receptacle

located on the MicroMAX's panel (labeled ANTENNA), as displayed below.

Содержание 605-0000-742




















































































Результаты поиска

Содержание 605-0000-742

Отзывы:

Бренды по названию

Популярные бренды

Airspan 605-0000-742, Установка оборудования

Результаты поиска

Содержание 605-0000-742

Отзывы:

Бренды по названию

Популярные бренды