AirSep AS-E, Инструкция по эксплуатации

Страница: 117 / 198

AS-D+—AS-P Series Instruction Manual 117
AirSep Corporation
Richland, MI 49083 Tel: (269) 629-5000
Installation & Service Instructions:
83-536-000
MICROalescer® Filter
ISSUED: September, 2006
Supersedes: July, 2004
Doc. #83-536-000, ECN# 060870, Rev. 3
WARNING: IF YOUR UNIT HAS A PLASTIC BOWL:
1.
DO NOT use plastic bowl units without a bowl guard installed.* Plastic
bowl units are sold only with bowl guards to minimize the danger of flying
fragments in the event of bowl failure. If this unit is in service without a
bowl guard installed, manufacturer's warranties are void, and the
manufacturer assumes no responsibility for any resulting loss.
(*EXCEPT
M00 MODEL)
2. DO NOT install the unit where it will be subjected to temperatures higher
than 125°F (52°C).
3.
DO NOT install the unit where it will be subjected to pressures higher
than 150 psig (10.3 bar).
4. CAUTION: Certain compressor oils, household cleaners, chemicals,
solvents, paints and fumes will attack plastic bowls and can cause
plastic bowl failure. See manufacturer's list shown elsewhere on this
sheet.
5. WHEN BOWL becomes dirty replace bowl or wipe only with a clean, dry
cloth.
6. DO NOT install on a compressed air line where the compressor is
lubricated with, or the air contains, a material that will attack plastic bowls.
7. DO inspect plastic bowls to detect crazing, cracking, damage or other
deterioration. Immediately replace any crazed, cracked, damaged or
deteriorated bowl with a metal bowl or a new plastic bowl and bowl guard.
8.
IF A UNIT HAS BEEN IN SERVICE AND DOES NOT HAVE A BOWL
GUARD, ORDER ANOTHER ONE AND INSTALL BEFORE PLACING
BACK IN SERVICE.
IMPORTANT INSTALLATION INSTRUCTIONS FOR
MICROALESCER® FILTERS (TYPE C)
1. DO NOT install the unit until you have read this entire product
information sheet. If your unit has a plastic bowl, note the special
warning information listed above.
2. EXCEPT as otherwise specified by manufacturer, this product is
specifically designed for compressed air service, and use with any other
fluid (liquid or gas) is a misapplication. For example, use with or injection
of certain hazardous liquids or gases in the system (such as alcohol or
liquid petroleum gas) could be harmful to the unit or result in a
combustible condition or hazardous external leakage. Before using with
fluids other than air, or for non-industrial applications, or for life support
systems, consult manufacturer for written approval. Manufacturer's
E N G L I S H
Acetaldehyde Carbon disulfide Ethylene dichloride Propionic acid
Acetic acid (conc.) Carbon tetrachloride Ethylene glycol Pyridine
Acetone Caustic potash solution Formaic acid (conc.) Sodium hydroxide
Acrylonitrile Caustic soda solution Freon (refrig.and propell) Sodium sulfide
Ammonia Chlorobenzine Gasoline (high aromatic) Styrene
Ammonium flouride Chloroform Hydrazine Sulfuric acid (conc.)
Ammonium hydroxide Cresol Hydrochloric acid (conc.) Sulphural chloride
Ammonium sulfide Cyclohexanol Methylene chloride Thiophene
Anaerobic adhesives Cyclohexanone Methylene salicylate Toluene
and sealants Cyclohexene Milk of lime (CaOH) Turpentine
Antifreeze Dimethyl formamide Nitric acid(conc.) Sulfuric acid (conc.)
Benzene Dioxane Nitrobenzine Sulphural chloride
Benzoic acid Ethane tetrachloride Nitrocellulose laquer Tetrahydronaphtalene
Benzyl alcohol Ethyl acetate Perchlorethylene Thiophene
Brake fluids Ethyl ether Phenol Toluene
Bromobenzine Ethylamine Phosphorous hydroxy chloride Turpentine
Butyric acid Ethylene chlorohydrin Phosphorous trichloride Xylene and others
Carbolic acid
TRADE NAMES OF SOME COMPRESSOR OILS, RUBBER COMPOUNDS AND OTHER MATERIALS
THAT WILL ATTACK POLYCARBONATE PLASTIC BOWLS
Atlas “Perma-Guard” Houghton and Co. oil Petron PD287 Stauffer Chemical
Buna N* #1120, #1130 & #1055 Prestone FYRQUEL #150
Cellulube #510 Houtosafe 1000 Pydraul AC Tannergas
and #250 Kano Kroil Sears Regular Motor Oil Telar
Crylex #5 cement Keystone penetrating oil #2 Sinclair oil “Lily White” Tenneco anderol
*Eastman 910 Marvel Mystery Oil Some Loctite Compounds #495 and #500 oils
Garlock #98403 Minn. Rubber 366Y Stillman #269-75 Titon
(polyurethane) National Compound #N11 (polyurethane) Zerex
Haskel #568-023 “Nylock” VC 3 Stillman #SR-513
Hilgard Co's hil phene Parco #1306 Neoprene (neoprene)
SOME OF THE MATERIALS THAT WILL ATTACK POLYCARBONATE PLASTIC BOWLS.
WE CANNOT POSSIBLY LIST ALL HARMFUL SUBSTANCES, CHECK WITH A MOBAY CHEMICAL
OR GENERAL ELECTRIC OFFICE FOR FURTHER INFORMATION ON POLYCARBONATE PLASTIC
WARNING
To avoid unpredictable system behavior that can cause personal injury
and property damage:
• Disconnect electrical supply (when necessary) before installation,
servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to
this product before installation, servicing, or conversion.
• Operate within the manufacturer’s specified pressure, temperature,
and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below
freezing.
• Service according to procedures listed in these instructions.
• Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical supplies
(when necessary) should be connected and the product tested for
proper function and leakage. If audible leakage is present, or the
product does not operate properly, do not put into use.
• Warnings and specifications on the product should not be covered
by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
!
!
CAUTION
Polycarbonate bowls, being transparent and tough, are ideal for use with
Filters and Lubricators. They are suitable for use in normal industrial
environments, but should not be located in areas where they could be subjected
to direct sunlight, an impact blow, nor temperatures outside of the rated
range. As with most plastics, some chemicals can cause damage.
Polycarbonate bowls should not be exposed to chlorinated hydrocarbons,
ketones, esters and certain alcohols. They should not be used in air systems
where compressors are lubricated with fire-resistant fluids such as phosphate
ester and di-ester types.
Metal bowls are recommended where ambient and/or media conditions are
not compatible with polycarbonate bowls. Metal bowls resist the action of
most such solvents, but should not be used where strong acids or bases are
present or in salt laden atmospheres. Consult the factory for specific
recommendations where these conditions exist.
TO CLEAN POLYCARBONATE BOWLS USE MILD SOAP AND WATER
ONLY! DO NOT use cleansing agents such as acetone, benzene, carbon
tetrachloride, gasoline, toluene, etc., which are damaging to this plastic.
Bowl guards are recommended for added protection of polycarbonate bowls where
chemical attack may occur.
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE
PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED
ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY
DAMAGE.
This document and other information from The Company, its subsidiaries
and authorized distributors provide product and/or system options for further
investigation by users having technical expertise. It is important that you
analyze all aspects of your application, including consequences of any
failure and review the information concerning the product or systems in the
current product catalog. Due to the variety of operating conditions and
applications for these products or systems, the user, through its own analysis
and testing, is solely responsible for making the final selection of the products
and systems and assuring that all performance, safety and warning
requirements of the application are met.
The products described herein, including without limitation, product features,
specifications, designs, availability and pricing, are subject to change by
The Company and its subsidiaries at any time without notice.
EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR
INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE
THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.
!
Safety Guide
For more complete information on recommended application guidelines, see the
Safety Guide section of Pneumatic Division catalogs or you can download the
Pneumatic Division Safety Guide at: www.wilkersoncorp.com