AirMan PDS100S-6B4 Скачать руководство пользователя страница 54

Страница: 54 / 65

6. Maintenance/Adjustment

Symptom Cause Countermeasures

Engine oil

pressure lamp goes

on.

(1) Engine oil shortage.

(2) Engine oil filter clogging.

(3) Malfunction of engine oil pump
(4) Faulty oil pressure switch.

(5) Loosened or disconnected wiring or

connector.

Replenish oil

Change

Change
Change

Check/Fasten

Coolant
temperature lamp

goes on.

(1) Radiator clogging.
(2) Faulty thermostat.

(3) Faulty coolant temperature switch.

(4) Shortage of coolant.

(5) Slippage of fan belt.
(6) Looseness, disconnection of wiring or

connectors.

Clean
Change

Change

Replenish

Adjust tension
Check/Fasten

Discharge air

temperature lamp
goes on.

(1) Oil cooler clogging.

(2) Oil filter clogging.
(3) Faulty discharged air temperature

switch.

(4) Looseness, disconnection of wiring or

connectors.

(5) Slippage of fan belt.

(6) Shortage of compressor oil.
(7) Malfunction of by-pass valve.

Clean

Change
Check/Change

Check/Fasten

Adjust tension

Replenish oil

Fuel residual level
lamp goes on.

(1) Fuel runs short.
(2) Malfunction of sending unit for fuel oil

level drop.

(3) Loosened and disconnected wiring

connection and connectors.

Add fuel oil
Inspect/replace

Inspect/retighten

Contact your nearest dealer if you find it difficult to repair by yourselves.

Refer to the engine operation manual for trouble concerning the engine.

Discount-Equipment.com

Содержание PDS100S-6B4


































































Результаты поиска

Содержание PDS100S-6B4

Отзывы:

AirMan PDS100S-6B4, Инструкция по эксплуатации, Страница: 54 / 65

Результаты поиска

Содержание PDS100S-6B4

Отзывы: