AirMan PDS100S-6B4 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 65

AirMan PDS100S-6B4 Скачать руководство пользователя страница 13

1. Safety

1

-

9

Draining separator receiver tank

After stopping the engine, confirm that the pressure gauge
indicates 0 psi (0 bar) and there is no residual pressure in it,
then open the drain valve gradually to drain the compressor oil.

Note residual pressure in the separator receiver tank could
force both extremely hot compressed air and oil to jet out and
you may be scalded or seriously injured.

H990432

Be careful of high-pressurized air blowout

After stopping the engine, make sure that pressure gauge
indicates 0 psi (0 bar). Even when the gauge shows 0 psi (0
bar), open a service valve and further do not fail to make sure
that there is no residual pressure in the air piping. Then begin
repair and maintenance.

Residual air under pressure can cause severe injury.

W010

Adjusting tension of fan belt

Be sure to stop the engine and remove the starter key
whenever the tension of the fan belt is to be adjusted.

Remove the negative (–) side cable from the battery.

If the machine is running, it might catch the operator’s hand
into the fan belts, and this could cause a serious injury.

TR0304

Hands off from cooling fan

Be sure to stop the engine and remove the starter key
whenever check or maintenance work is carried out near the
cooling fan.

If the cooling fan is rotating, it may catch the operator or part of
his body into the fan, and it could cause a serious injury.

W009

Discount-Equipment.com

«
...
11
12
13
14
15
...
»

Содержание PDS100S-6B4


































































Отзывы:

Нет отзывов