AirMan PDS100S-6B4 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 65

AirMan PDS100S-6B4 Скачать руководство пользователя страница 12

1. Safety

1

-

8

Fire prevention

Do not, under any circumstance, bring lit cigarettes or matches
near oils as engine oil and compressor oil, etc.
They are extremely flammable and dangerous.

Refilling oils should be done in an outdoor well-ventilated
place.

Refuel after stopping the engine, and never leave the fuel
nearby the machine. Do not spill. Clean environmental spills.

Such parts as muffler and exhaust pipe can be extremely hot.
Remove twigs, dried leaves, dried grass and waste paper, etc.
from the exhaust outlet of the muffler.

Keep a fire extinguisher available by the machine in case of a
fire.

D004

H990433

1.3 Caution during Inspection and Maintenance

Hang a “Now Checking and under Maintenance” tag

Remove the starter key from the starter switch before starting
inspection, and hang up a “Now Checking and under
Maintenance” tag where it can be easily seen. The checker
must keep the key during checking and maintenance.

Remove the negative (–) side cable from the battery.

SY001

Refilling of compressor oil

When you refill the separator receiver tank with compressor oil,
stop the engine, and make sure that the pressure gauge
indicates 0 psi (0 bar) and there is no residual pressure in it,
and then gradually loosen the oil filler cap for refilling oil.

Note residual pressure in the separator receiver tank could
force both extremely hot compressed air and oil to jet out and
you may be scalded or seriously injured.

W010

Discount-Equipment.com

«
...
10
11
12
13
14
...
»

Содержание PDS100S-6B4


































































Отзывы:

Нет отзывов