Air-Pol Feniks FUTURE Скачать руководство пользователя страница 27

Страница: 27 / 36

Feniks FUTURE Instruction Manual, No.

033-02-200

edition

, 2012, page

AIR-POL Sp. z o.o.

– 05-120 Legionowo, ul. Olszankowa 52, www.air-pol.com.pl

tel.: (+4822) 774 0711, (+4822) 784 1595, (+4822) 774 4832, fax (+4822) 784 9640, @: [email protected]

CLOSING THE BAG WITH THE HAND-DEPLOYED COLLAPSIBLE PILOT CHUTE ATTACHED

Assemble the main parachute following guidelines specified in Section Four item 5 of the Instruction Manual.

Before placing the canopy in the bag check the condition of the rubber stows. They should be of appropriate type, all of the

same kind and grade, and undamaged. Replace stows if necessary.

•

For “Dacron” lines we recommend the use of rubber stows 4 cm in diameter (~6 cm once the band is folded).

•

For Microlines (Spectra, Vectran, HMA, etc.) use rubber stows 2 cm in diameter (~3 cm once the band is folded).

Photo No. 59

Fold the canopy, the leading edge, and the

trailing edge, and determine the position of the

slider by following guidelines specified in the

owner’s manual of the given canopy.

The folded parachute canopy should be

approximately 5 cm wider than the bag. This

allows for the bag to be well filled, resulting in

a more favourable bag shape.

Photo No. 60

Before placing the canopy in the bag you have

to open, or “arm” the kill-line. The photograph

shows the collapsible pilot chute (1), the

connecting tape (2), and the canopy bag (3)

prior to arming. The top of the pilot chute (4)

has been pulled in next to the end of the

connecting tape, with the inner connecting

tape length (5) extended.

Photo No. 61

“Arm” the kill-line system by stretching the top

of the collapsible pilot chute (4) to open it fully,

drawing the point of attachment to the canopy

as close as possible to the eye inside the

canopy bag. The inner line shall be threaded

over to the pilot chute side, while the

connecting tape length inside the bag (5) shall

remain wrinkled.

The window (6) on the other side of the

closing pin tuck an inner line marked in

contrasting colour should be visible.

ATTENTION!

Using a parachute with an “unarmed” (unopened) collapsible pilot chute may result in a failure of the main parachute

container to open, causing a pilot chute in tow malfunction.

Place the folded canopy in the bag. Check for parachute canopy fabric trapped between the canopy attachment point,

connecting tape, and the eye of the bag – trapped fabric may be damaged during the deployment process.

Содержание Feniks FUTURE





































Результаты поиска

Содержание Feniks FUTURE

Отзывы:

Похожие инструкции для Feniks FUTURE

Бренды по названию

Популярные бренды

Air-Pol Feniks FUTURE, Инструкция по эксплуатации

Результаты поиска

Содержание Feniks FUTURE

Отзывы:

Похожие инструкции для Feniks FUTURE

Бренды по названию

Популярные бренды