Aim-TTI MX100Q Скачать руководство пользователя страница 40

Страница: 40 / 46

Page 39

12.2.4 Interface Management Commands

LOCAL

Go to local. Any subsequent command will restore the remote state.

IFLOCK

NRF

Set or Clear the lock requiring the instrument to respond only to this

interface, where <

NRF

> has the meaning: 0 = clear and 1 = set the lock.

It is an Execution Error (number 200) if the request is denied either because

of conflict with a lock on this or another interface, or the user has disabled

this interface from taking control using the web interface.

IFLOCK?

Query the status of the interface lock.

The response is: <

1><

RMT

> where <

1> is

= 0 if there is no active lock,

= 1 if this interface instance owns the lock or

= -1 if the lock is unavailable either because it is in use by another interface

or the user has disabled this interface from taking control (via the web

interface).

ADDRESS?

Returns the GPIB bus Address. The response is <

1><

RMT

IPADDR?

Returns the present IP address of the LAN interface, provided it is

connected.

If it is not connected, the response will be the static IP if configured to

always use that static IP, otherwise it will be 0.0.0.0 if waiting for DHCP or

Auto-IP.

The response is nnn.nnn.nnn.nnn<

RMT

>, where each nnn is 0 to 255.

NETMASK?

Returns the present netmask of the LAN interface, provided it is connected.

The response is nnn.nnn.nnn.nnn<

RMT

>, where each nnn is 0 to 255.

NETCONFIG? Returns the first means by which an IP address will be sought.

The response is <

CRD

RMT

> where <

CRD

> is DHCP, AUTO or STATIC.

The following commands specify the parameters to be used by the LAN interface.

Note:

power cycle is required after these commands are sent before the new settings are used (or

returned in response to the queries listed above). The instrument does not attempt to check the

validity of the IP address or netmask in any way other than checking that each part fits in 8 bits.

The rear panel LAN RESET switch will override these commands and restore the defaults as

described earlier.

NETCONFIG

CPD

Specifies the first means by which an IP address will be sought.

CPD

> must be one of DHCP, AUTO or STATIC.

IPADDR

<QUAD>

Sets the potential static IP address of the LAN interface (as on the

webpage).

The parameter must be strictly a dotted quad for the IP address, with each

address part an <

1> in the range 0 to 255, (e.g. 192.168.1.101).

NETMASK

<QUAD>

Sets the netmask to accompany the static IP address of the LAN interface.

The parameter must be strictly a dotted quad for the netmask, with each

part an <

1> in the range 0 to 255, (e.g. 255.255.255.0).

Содержание MX100Q















































Результаты поиска

Содержание MX100Q

Отзывы:

Похожие инструкции для MX100Q

Бренды по названию

Популярные бренды

Aim-TTI MX100Q, Инструкция по эксплуатации

Результаты поиска

Содержание MX100Q

Отзывы:

Похожие инструкции для MX100Q

Бренды по названию

Популярные бренды